1|Page
CCNA 1 FINAL EXAM WITH VERIFIED
SOLUTIONS
A network administrator is tasked with connecting two workgroups that are
configured to use different subnets. Which device should be selected to allow
connectivity between users on the two networks?-correct-answer-Router
Which two programs can be used to accomplish terminal emulation for
configuring a router from the CLI through the console port? (Choose two.)-
correct-answer-HyperTerminal;
Minicom
Which statement accurately describes file sharing in a peer-to-peer network?-
correct-answer-Access control is decentralized.
What are two primary responsibilities of the Ethernet MAC sublayer? (Choose
two.)-correct-answer-data encapsulation;
accessing the media
,2|Page
Which router configuration mode would an administrator use to configure the
router for SSH or Telnet login access?-correct-answer-Line
Refer to the exhibit. Which device should be included in the network topology to
provide Layer 2 connectivity for all LAN devices, provide multiple collision
domains, and also provide a connection to the rest of the network?-correct-
answer-Switch
Refer to the exhibit. A technician has been asked to test connectivity from PC1 to a
remote network. Which action will indicate if there is remote connectivity?-
correct-answer-C:\>ping 172.16.4.1
What purpose does a hostname serve on a router?-correct-answer-provides
device identification to users logging on remotely
Which prompt is associated with the privileged exec mode?-correct-answer-R1#
A technician wishes to connect two computers to move data from one to the
other before reloading the operating system. The NICs on both PCs do not support
autosensing feature. Which procedure will satisfy the requirement?-correct-
answer-Interconnect the two PCs with a crossover cable.
, 3|Page
Refer to the exhibit. Interface Fa0/0 on router A is generating excessive broadcast
traffic. Which LAN segments will affected by the excessive broadcasts?-correct-
answer-Only the 192.168.1.200/30 network will be affected.
Two routers are connected via their serial ports in a lab environment. The routers
are configured with valid IP addresses, but they cannot ping each other. The show
interface serial0/0 command shows that the serial0/0 interface is up but the line
protocol is down. What could be the cause of this problem?-correct-answer-The
clock rate command has not been entered on the DCE interface.
Refer to the exhibit. Which layered network model is shown in the diagram?-
correct-answer-TCP/IP
Refer to the exhibit. Host A is unable to reach host B on the remote network. A
technician attempted to ping the local gateway and the ping was successful. To
verify the host configuration, the technician issued the ipconfig command. What is
the likely cause of the problem?-correct-answer-The default gateway on host A is
incorrectly configured.
Which option shows how a router will route packets to a remote network?-
correct-answer-Image 4
CCNA 1 FINAL EXAM WITH VERIFIED
SOLUTIONS
A network administrator is tasked with connecting two workgroups that are
configured to use different subnets. Which device should be selected to allow
connectivity between users on the two networks?-correct-answer-Router
Which two programs can be used to accomplish terminal emulation for
configuring a router from the CLI through the console port? (Choose two.)-
correct-answer-HyperTerminal;
Minicom
Which statement accurately describes file sharing in a peer-to-peer network?-
correct-answer-Access control is decentralized.
What are two primary responsibilities of the Ethernet MAC sublayer? (Choose
two.)-correct-answer-data encapsulation;
accessing the media
,2|Page
Which router configuration mode would an administrator use to configure the
router for SSH or Telnet login access?-correct-answer-Line
Refer to the exhibit. Which device should be included in the network topology to
provide Layer 2 connectivity for all LAN devices, provide multiple collision
domains, and also provide a connection to the rest of the network?-correct-
answer-Switch
Refer to the exhibit. A technician has been asked to test connectivity from PC1 to a
remote network. Which action will indicate if there is remote connectivity?-
correct-answer-C:\>ping 172.16.4.1
What purpose does a hostname serve on a router?-correct-answer-provides
device identification to users logging on remotely
Which prompt is associated with the privileged exec mode?-correct-answer-R1#
A technician wishes to connect two computers to move data from one to the
other before reloading the operating system. The NICs on both PCs do not support
autosensing feature. Which procedure will satisfy the requirement?-correct-
answer-Interconnect the two PCs with a crossover cable.
, 3|Page
Refer to the exhibit. Interface Fa0/0 on router A is generating excessive broadcast
traffic. Which LAN segments will affected by the excessive broadcasts?-correct-
answer-Only the 192.168.1.200/30 network will be affected.
Two routers are connected via their serial ports in a lab environment. The routers
are configured with valid IP addresses, but they cannot ping each other. The show
interface serial0/0 command shows that the serial0/0 interface is up but the line
protocol is down. What could be the cause of this problem?-correct-answer-The
clock rate command has not been entered on the DCE interface.
Refer to the exhibit. Which layered network model is shown in the diagram?-
correct-answer-TCP/IP
Refer to the exhibit. Host A is unable to reach host B on the remote network. A
technician attempted to ping the local gateway and the ping was successful. To
verify the host configuration, the technician issued the ipconfig command. What is
the likely cause of the problem?-correct-answer-The default gateway on host A is
incorrectly configured.
Which option shows how a router will route packets to a remote network?-
correct-answer-Image 4
