FMC test |77 Complete Questions and Answers
When should alarm and pressure holding test be performed on dialysis machine - -Before
each treatment
-In order to determine the adequacy of a dialysis treatment which of these laboratory
values should be evaluated - -Blood urea nitrogen
-What is the purpose of maintaining a log of water quality checks - -To prove safe water
has been documented
-When is the correct time to draw a post bun - -Before returning the patient's blood
-Which of these parameters on the hemodialysis machine must be verified pretreatment
buy an external measuring device - -PH and connectivity
-The heater on the hemodialysis machine has a malfunction and as a result the
temperature of the dialysis has risen above 105 Fahrenheit what complication is likely to
occur - -Hemolysis
-The patient has completed their treatment the PCT SS the patient to the scale to be
weighed suddenly the patient tells the PCT she does not feel well she complains of being
dizzy what should the PCT do next - -Call the nurse to assist a patient
-The purpose of reverse osmosis device is - -To provide high-quality high quantity water
-It is important to monitor pump pressure on the reverse osmosis device to - -Determine
changes that may affect product or waste water flow
-The water softner exchanges sodium ions for - -Calcium and magnesium ions
-When teaching a patient about prevention of hypotension during the treatment the nurse
should include which of these instructions - -Always take prescribed medication at least 30
minutes prior to treatment
-Which of the following has the highest potassium content - -Bananas orange juice and salt
-The group of symptoms that include feelings of fainting and double vision irritated and
hunger may be associated with what patient complication - -Hypoglycemia
-When caring for a patient who is Hepatitis B positive after disconnecting the bloodlines
what must the technician do before documenting - -Remove gloves sanitize hands and put
on a fresh pair of gloves
-According to FMC policy the safe level for total chlorine is - -Less than 0.10PPM
, -The purpose of the carbon tanks in dialysis is to - -Remove chlorine and chloramine from
feed water
-Join the setup all the dialysis machine A co-worker states that the PCT has contaminated
the circuit which of the following would be most likely source of contamination - -The
Bloodlines are in the prime bucket with open end caps
-The function of the blending valve in the water treatment system is to - -Mix hot and cold
water to achieve an acceptable temperature
-Available weight gain is described as the - -Pretreatment weight minus dry weight
-Doing safety checks the technician notes the following which one requires intervention - -
Access and the patients face are covered
-Use of a diasafe filters allows the production of - -Ultrapure dialysate
-Which alarm will not stop the blood pump - -Blood pressure alarm
-Dialysate used for in center hemodialysis is - -Non sterile and biocompatible
-The patient comes to dialysis with complaints of cramping since last treat. The clinician
should. - -Look at previous dialysis flow sheets to evaluate adjustment of Target weight
-Which component of the water treatment system must never be bypassed - -carbon tanks
-The venous pressure on the dialysis machine starts to rise but the Venus needle is not
infiltrated the rise is most likely due 2 - -The acccess clotting
-When should the water be checked for total chlorine during routine operations of the
outpatient facility - -Before the first treatment is started before each shift begins or not to
exceed four hours
-Normal saline is used to rinse and prime the tubing of the extracorporeal circuit to
remove - -Sterilant and air
-A patient begins to experience shortness of breath chest pain and sudden hypertension
the blood is bright red and translucent the complication most likely occurring is - -
hemolysis
-During dialysis a patient has a cardiac arrest which action should be completed on the
dialysis machine before the machine is used by another patient - -Technical must perform
a functional test on the machine
-To properly collect a post bun sample it is necessary to - -turn off ultrafiltration rate
When should alarm and pressure holding test be performed on dialysis machine - -Before
each treatment
-In order to determine the adequacy of a dialysis treatment which of these laboratory
values should be evaluated - -Blood urea nitrogen
-What is the purpose of maintaining a log of water quality checks - -To prove safe water
has been documented
-When is the correct time to draw a post bun - -Before returning the patient's blood
-Which of these parameters on the hemodialysis machine must be verified pretreatment
buy an external measuring device - -PH and connectivity
-The heater on the hemodialysis machine has a malfunction and as a result the
temperature of the dialysis has risen above 105 Fahrenheit what complication is likely to
occur - -Hemolysis
-The patient has completed their treatment the PCT SS the patient to the scale to be
weighed suddenly the patient tells the PCT she does not feel well she complains of being
dizzy what should the PCT do next - -Call the nurse to assist a patient
-The purpose of reverse osmosis device is - -To provide high-quality high quantity water
-It is important to monitor pump pressure on the reverse osmosis device to - -Determine
changes that may affect product or waste water flow
-The water softner exchanges sodium ions for - -Calcium and magnesium ions
-When teaching a patient about prevention of hypotension during the treatment the nurse
should include which of these instructions - -Always take prescribed medication at least 30
minutes prior to treatment
-Which of the following has the highest potassium content - -Bananas orange juice and salt
-The group of symptoms that include feelings of fainting and double vision irritated and
hunger may be associated with what patient complication - -Hypoglycemia
-When caring for a patient who is Hepatitis B positive after disconnecting the bloodlines
what must the technician do before documenting - -Remove gloves sanitize hands and put
on a fresh pair of gloves
-According to FMC policy the safe level for total chlorine is - -Less than 0.10PPM
, -The purpose of the carbon tanks in dialysis is to - -Remove chlorine and chloramine from
feed water
-Join the setup all the dialysis machine A co-worker states that the PCT has contaminated
the circuit which of the following would be most likely source of contamination - -The
Bloodlines are in the prime bucket with open end caps
-The function of the blending valve in the water treatment system is to - -Mix hot and cold
water to achieve an acceptable temperature
-Available weight gain is described as the - -Pretreatment weight minus dry weight
-Doing safety checks the technician notes the following which one requires intervention - -
Access and the patients face are covered
-Use of a diasafe filters allows the production of - -Ultrapure dialysate
-Which alarm will not stop the blood pump - -Blood pressure alarm
-Dialysate used for in center hemodialysis is - -Non sterile and biocompatible
-The patient comes to dialysis with complaints of cramping since last treat. The clinician
should. - -Look at previous dialysis flow sheets to evaluate adjustment of Target weight
-Which component of the water treatment system must never be bypassed - -carbon tanks
-The venous pressure on the dialysis machine starts to rise but the Venus needle is not
infiltrated the rise is most likely due 2 - -The acccess clotting
-When should the water be checked for total chlorine during routine operations of the
outpatient facility - -Before the first treatment is started before each shift begins or not to
exceed four hours
-Normal saline is used to rinse and prime the tubing of the extracorporeal circuit to
remove - -Sterilant and air
-A patient begins to experience shortness of breath chest pain and sudden hypertension
the blood is bright red and translucent the complication most likely occurring is - -
hemolysis
-During dialysis a patient has a cardiac arrest which action should be completed on the
dialysis machine before the machine is used by another patient - -Technical must perform
a functional test on the machine
-To properly collect a post bun sample it is necessary to - -turn off ultrafiltration rate
