SDI FIREARM FINISHES AND ENGRAVING (FTT 201)
EXAM NEWEST 2025 ACTUAL EXAM WITH COMPLETE
110+ QUESTIONS AND CORRECT DETAILED ANSWERS
(VERIFED ANSWERS) ALREADY GRADED A+ |
GUARANTEED PASS
When placing the project in the tank, you should ______________ and
then __________________. - Correct Answer > Hold it at a 30 degree angle;
Submerge it slowly and consistently
Dan Herman suggests that you use a _________________________ for
mixing acids, because of the amount of heat which can be produced. -
Correct Answer > Pyrex Glass Beaker
For cold and slow-rust bluing, _______________ is critical to a
satisfactory end result. - Correct Answer > Cleanliness
The fire lapping process involves: - Correct Answer > Firing cartridges with
progressively finer grit abrasive coated bullets, which effectively
polishes the bore.
,After removing the object from the dipping tank: - Correct Answer > Wait 60
seconds and then rinse the project with a clean, gentle spray of water
Joe Carlos' experiment showed that electropolishing was: - Correct Answer >
Effective for Increasing the Accuracy of Damaged Barrels
T/F: Fire lapping has about the same average effective improvement on
accuracy as electropolishing. - Correct Answer > TRUE
There is generally more need for fire lapping in: - Correct Answer > Button
Rifled Bores
T/F: Fire lapping does not remove metal from the barrel. - Correct Answer >
FALSE
"Throat maintenance" bullets were found through extensive testing to: -
Correct Answer > Have a reliably positive impact on accuracy
The two basic metal preparation processes, according to Frank Fry, are:
- Correct Answer > Hand and Machine
The first of three steps to hand finishing is: - Correct Answer > Remove machine
marks with files
, Which of the following wheel types used in machine polishing will cut
the fastest? - Correct Answer > Felt
To prevent the loss of or "pulling" of letters and numbers, these areas
should be polished by: - Correct Answer > Hand
When using a wheel for polishing: - Correct Answer > Always polish with sharp
edges pointed in the same direction the wheel is turning.
If stamping has been damaged or pitted, you should: - Correct Answer > Leave
the damaged stamping alone
Nickel plating has been a popular finish for handguns and certain small
parts of long guns since the turn of the century. The finish is applied by
a process called: - Correct Answer > Electroplating
For basic polishing: protect all of the newly-polished surfaces from
rusting with which of the following until you are ready to apply the
bluing solution: - Correct Answer > Light Coat of Oil
In general, power polishing entails starting which of the following grits
and polishing the surface of the metal in a given direction: - Correct Answer >
Coarset
EXAM NEWEST 2025 ACTUAL EXAM WITH COMPLETE
110+ QUESTIONS AND CORRECT DETAILED ANSWERS
(VERIFED ANSWERS) ALREADY GRADED A+ |
GUARANTEED PASS
When placing the project in the tank, you should ______________ and
then __________________. - Correct Answer > Hold it at a 30 degree angle;
Submerge it slowly and consistently
Dan Herman suggests that you use a _________________________ for
mixing acids, because of the amount of heat which can be produced. -
Correct Answer > Pyrex Glass Beaker
For cold and slow-rust bluing, _______________ is critical to a
satisfactory end result. - Correct Answer > Cleanliness
The fire lapping process involves: - Correct Answer > Firing cartridges with
progressively finer grit abrasive coated bullets, which effectively
polishes the bore.
,After removing the object from the dipping tank: - Correct Answer > Wait 60
seconds and then rinse the project with a clean, gentle spray of water
Joe Carlos' experiment showed that electropolishing was: - Correct Answer >
Effective for Increasing the Accuracy of Damaged Barrels
T/F: Fire lapping has about the same average effective improvement on
accuracy as electropolishing. - Correct Answer > TRUE
There is generally more need for fire lapping in: - Correct Answer > Button
Rifled Bores
T/F: Fire lapping does not remove metal from the barrel. - Correct Answer >
FALSE
"Throat maintenance" bullets were found through extensive testing to: -
Correct Answer > Have a reliably positive impact on accuracy
The two basic metal preparation processes, according to Frank Fry, are:
- Correct Answer > Hand and Machine
The first of three steps to hand finishing is: - Correct Answer > Remove machine
marks with files
, Which of the following wheel types used in machine polishing will cut
the fastest? - Correct Answer > Felt
To prevent the loss of or "pulling" of letters and numbers, these areas
should be polished by: - Correct Answer > Hand
When using a wheel for polishing: - Correct Answer > Always polish with sharp
edges pointed in the same direction the wheel is turning.
If stamping has been damaged or pitted, you should: - Correct Answer > Leave
the damaged stamping alone
Nickel plating has been a popular finish for handguns and certain small
parts of long guns since the turn of the century. The finish is applied by
a process called: - Correct Answer > Electroplating
For basic polishing: protect all of the newly-polished surfaces from
rusting with which of the following until you are ready to apply the
bluing solution: - Correct Answer > Light Coat of Oil
In general, power polishing entails starting which of the following grits
and polishing the surface of the metal in a given direction: - Correct Answer >
Coarset
