ASNT LEVEL 3 EXAM ACTUAL
EXAM (BASIC MATERIALS AND
PROCESSES EXAM) | ALL
QUESTIONS AND CORRECT
ANSWERS | GRADED A+ | LATEST
EXAM 2025 | VERIFIED ANSWERS
Save
Terms in this set (175)
What are the One for the answers was from 250-
minimum and 450°F which is less than 850°F
maximum solder where brazing starts.
temperatures?
,What 850°F
temperature
does brazing
start?
1 Conversion of Curie to Bq
curie(Ci)=3.7x10^
10 becquerel(Bq)
A UT inspection Pitch/Catch
that uses two
transducers on
one side of the
part- This
technique is
known?
Laminations parallel to the surface.
A UT angle
Watch out for one answer as it has
beam inspection
perpendicular to the surface and
is most apt to
angle beam can see this type of
miss what?
indication.
, A UT inspection A DAC curve. Whether it is brought
that utilizes a to horizontal, or left as a curved line,
diagram made it is known as a reference line.
from the same
size flat bottom
holes at different
distances? This is
known as?
If material is thicker that 3/4", the
What would
normal amperages are considered
amperage used
to be 125 amperages for each inch
for prod spacing
of spacing. Therefore, the answer
for material
would be 125 x 5= 625 amps. The
thickness of one
answer was 500- 625 amps. Note: if
inch using a
material is thinner than 3/4", the
spacing of five
amperage is 90-100 amps per inch,
inches?
or 400-500 amps.
What type of Half wave DC (Mean Amps). Some
current is usually MT probes have switch to allow
used for either AC(RMS amps) or
portable HWDC(Mean amps). They're also
magnetic probes that only uses AC.
particle probe?
EXAM (BASIC MATERIALS AND
PROCESSES EXAM) | ALL
QUESTIONS AND CORRECT
ANSWERS | GRADED A+ | LATEST
EXAM 2025 | VERIFIED ANSWERS
Save
Terms in this set (175)
What are the One for the answers was from 250-
minimum and 450°F which is less than 850°F
maximum solder where brazing starts.
temperatures?
,What 850°F
temperature
does brazing
start?
1 Conversion of Curie to Bq
curie(Ci)=3.7x10^
10 becquerel(Bq)
A UT inspection Pitch/Catch
that uses two
transducers on
one side of the
part- This
technique is
known?
Laminations parallel to the surface.
A UT angle
Watch out for one answer as it has
beam inspection
perpendicular to the surface and
is most apt to
angle beam can see this type of
miss what?
indication.
, A UT inspection A DAC curve. Whether it is brought
that utilizes a to horizontal, or left as a curved line,
diagram made it is known as a reference line.
from the same
size flat bottom
holes at different
distances? This is
known as?
If material is thicker that 3/4", the
What would
normal amperages are considered
amperage used
to be 125 amperages for each inch
for prod spacing
of spacing. Therefore, the answer
for material
would be 125 x 5= 625 amps. The
thickness of one
answer was 500- 625 amps. Note: if
inch using a
material is thinner than 3/4", the
spacing of five
amperage is 90-100 amps per inch,
inches?
or 400-500 amps.
What type of Half wave DC (Mean Amps). Some
current is usually MT probes have switch to allow
used for either AC(RMS amps) or
portable HWDC(Mean amps). They're also
magnetic probes that only uses AC.
particle probe?
