VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
4"
Protruding objects may not protrude
more than inches into the path of ANSI Accessible and Usable Buildings
travel. and Facilities, 2017
Page 15
1/2"
In new buildings, thresholds at doorways
ANSI Accessible and Usable Buildings
should be no higher than .
and Facilities, 2017
Page 30
34"
In a Type A unit, if measuring to the high-
est part of the rim or highest part of the
ANSI Accessible and Usable Buildings
counter, what is the maximum height of
and Facilities, 2017
the sink front above the floor?
Page 149
34" minimum, 38" maximum
The height of handrails shall be
minimum and maximum vertically
ANSI Accessible and Usable Buildings
above stair nosings, ramp and walking
and Facilities, 2017
surfaces.
Page 62
36"
A hallway more than 24 inches long must
ANSI Accessible and Usable Buildings
have a clear width of .
and Facilities, 2017
Page 19
Circle
Enter and proceed" is presented as a
on the raised touchable surface ANSI Accessible and Usable Buildings
on a function key." and Facilities, 2017
Page 107
Tight grasping, pinching, or twisting of
the wrist.
Operable parts shall be operable with
one hand and shall not require: ANSI Accessible and Usable Buildings
and Facilities, 2017
Page 18
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
32 inches
In existing buildings and facilities, the
clear width of a walking surface shall be
ANSI Accessible and Usable Buildings
permitted to be reduced to mini-
and Facilities, 2017
mum for a length of 24 inches maximum.
Page 19
36 inches
The clear width of an exterior accessible
route located within seating areas shall ANSI Accessible and Usable Buildings
be minimum. and Facilities, 2017
Page 19
1:20
The running slope of walking surfaces
ANSI Accessible and Usable Buildings
shall not be steeper than:
and Facilities, 2017
Page 19
Revolving doors & Turnstiles
What components shall not be part of an
ANSI Accessible and Usable Buildings
accessible route?
and Facilities, 2017
Page 19
54"
The maximum height of existing elevator
call buttons shall be permitted to be lo- ANSI Accessible and Usable Buildings
cated above the floor. and Facilities, 2017
Page 40
25"
The maximum knee clearance shall be
permitted to extend under an ele- ANSI Accessible and Usable Buildings
ment that is 9" above the floor. and Facilities, 2017
Page 13
5
The brightness of the elevator car land-
ing sill, threshold, platform and controls
ANSI Accessible and Usable Buildings
are to be no less than foot can-
and Facilities, 2017
dles.
Page 51
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
1-1/4"
What is the least diameter of grab bars
ANSI Accessible and Usable Buildings
with circular cross sections?
and Facilities, 2017
Page 87
34"
All hardware such as handles, locks, or
any other operable parts shall be ANSI Accessible and Usable Buildings
minimum above the floor. and Facilities, 2017
Page 32
0.05
In new construction, what is the maxi-
ANSI Accessible and Usable Buildings
mum slope of a ramp?
and Facilities, 2017
Page 33
60-inch
In existing buildings and facilities, the
turning space shall be a circular space ANSI Accessible and Usable Buildings
with a minimum diameter. and Facilities, 2017
Page 10
60"
What is the minimum diameter of a circu-
ANSI Accessible and Usable Buildings
lar turnaround area in a new building?
and Facilities, 2017
Page 10
Doorways shall have a clear opening 4 inches
width of 32 inches minimum. Projections
into the clear opening width between 34 ANSI Accessible and Usable Buildings
inches and 80 inches above the floor and Facilities, 2017
shall not exceed: Page 25
Install the top track first
What is the first step to placing a bifold
door? Carpentry and Building Construction -
Page 616
Camber
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
Glulams are sometimes manufactured
Carpentry and Building Construction -
with a slight upward curve known as
Page 361
?
When using a splash block to direct wa- 3'
ter from a down spout, how long should
it be to carry away water from the foun- Carpentry and Building Construction -
dation? Page 653
3
How many bundles are usually in a
square of 3-tab shingles? Carpentry and Building Construction -
Page 637
Water
What would be mixed into a concrete
mixture to control the wear resistance
Carpentry and Building Construction -
and stability of concrete?
Page 223
34-1/2"
What is the typical height of a regular
base kitchen cabinet? Carpentry and Building Construction -
Page 784
1/4"
A roll roofing strip should have at least
how many inches overlapping at the
Carpentry and Building Construction -
eave?
Page 629
Of the species commonly used in house Decay
construction, the heartwood of bald cy-
press, redwood, and various cedars is Carpentry and Building Construction -
highest in resistance. Page 329
Snap ties
Before concrete is placed, what is com-
monly used to secure the sides of foun-
Carpentry and Building Construction -
dation wall forms to prevent spreading?
Page 265
Dimension lines
On a blueprint, what do lines that end
with arrows represent? Carpentry and Building Construction -
Page 45
ANSWERS|100% PASS
4"
Protruding objects may not protrude
more than inches into the path of ANSI Accessible and Usable Buildings
travel. and Facilities, 2017
Page 15
1/2"
In new buildings, thresholds at doorways
ANSI Accessible and Usable Buildings
should be no higher than .
and Facilities, 2017
Page 30
34"
In a Type A unit, if measuring to the high-
est part of the rim or highest part of the
ANSI Accessible and Usable Buildings
counter, what is the maximum height of
and Facilities, 2017
the sink front above the floor?
Page 149
34" minimum, 38" maximum
The height of handrails shall be
minimum and maximum vertically
ANSI Accessible and Usable Buildings
above stair nosings, ramp and walking
and Facilities, 2017
surfaces.
Page 62
36"
A hallway more than 24 inches long must
ANSI Accessible and Usable Buildings
have a clear width of .
and Facilities, 2017
Page 19
Circle
Enter and proceed" is presented as a
on the raised touchable surface ANSI Accessible and Usable Buildings
on a function key." and Facilities, 2017
Page 107
Tight grasping, pinching, or twisting of
the wrist.
Operable parts shall be operable with
one hand and shall not require: ANSI Accessible and Usable Buildings
and Facilities, 2017
Page 18
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
32 inches
In existing buildings and facilities, the
clear width of a walking surface shall be
ANSI Accessible and Usable Buildings
permitted to be reduced to mini-
and Facilities, 2017
mum for a length of 24 inches maximum.
Page 19
36 inches
The clear width of an exterior accessible
route located within seating areas shall ANSI Accessible and Usable Buildings
be minimum. and Facilities, 2017
Page 19
1:20
The running slope of walking surfaces
ANSI Accessible and Usable Buildings
shall not be steeper than:
and Facilities, 2017
Page 19
Revolving doors & Turnstiles
What components shall not be part of an
ANSI Accessible and Usable Buildings
accessible route?
and Facilities, 2017
Page 19
54"
The maximum height of existing elevator
call buttons shall be permitted to be lo- ANSI Accessible and Usable Buildings
cated above the floor. and Facilities, 2017
Page 40
25"
The maximum knee clearance shall be
permitted to extend under an ele- ANSI Accessible and Usable Buildings
ment that is 9" above the floor. and Facilities, 2017
Page 13
5
The brightness of the elevator car land-
ing sill, threshold, platform and controls
ANSI Accessible and Usable Buildings
are to be no less than foot can-
and Facilities, 2017
dles.
Page 51
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
1-1/4"
What is the least diameter of grab bars
ANSI Accessible and Usable Buildings
with circular cross sections?
and Facilities, 2017
Page 87
34"
All hardware such as handles, locks, or
any other operable parts shall be ANSI Accessible and Usable Buildings
minimum above the floor. and Facilities, 2017
Page 32
0.05
In new construction, what is the maxi-
ANSI Accessible and Usable Buildings
mum slope of a ramp?
and Facilities, 2017
Page 33
60-inch
In existing buildings and facilities, the
turning space shall be a circular space ANSI Accessible and Usable Buildings
with a minimum diameter. and Facilities, 2017
Page 10
60"
What is the minimum diameter of a circu-
ANSI Accessible and Usable Buildings
lar turnaround area in a new building?
and Facilities, 2017
Page 10
Doorways shall have a clear opening 4 inches
width of 32 inches minimum. Projections
into the clear opening width between 34 ANSI Accessible and Usable Buildings
inches and 80 inches above the floor and Facilities, 2017
shall not exceed: Page 25
Install the top track first
What is the first step to placing a bifold
door? Carpentry and Building Construction -
Page 616
Camber
, VA HIC LIENCE FINAL EXAM/ VA HIC EXAM PRACTICE 2025 QUESTIONS AND
ANSWERS|100% PASS
Glulams are sometimes manufactured
Carpentry and Building Construction -
with a slight upward curve known as
Page 361
?
When using a splash block to direct wa- 3'
ter from a down spout, how long should
it be to carry away water from the foun- Carpentry and Building Construction -
dation? Page 653
3
How many bundles are usually in a
square of 3-tab shingles? Carpentry and Building Construction -
Page 637
Water
What would be mixed into a concrete
mixture to control the wear resistance
Carpentry and Building Construction -
and stability of concrete?
Page 223
34-1/2"
What is the typical height of a regular
base kitchen cabinet? Carpentry and Building Construction -
Page 784
1/4"
A roll roofing strip should have at least
how many inches overlapping at the
Carpentry and Building Construction -
eave?
Page 629
Of the species commonly used in house Decay
construction, the heartwood of bald cy-
press, redwood, and various cedars is Carpentry and Building Construction -
highest in resistance. Page 329
Snap ties
Before concrete is placed, what is com-
monly used to secure the sides of foun-
Carpentry and Building Construction -
dation wall forms to prevent spreading?
Page 265
Dimension lines
On a blueprint, what do lines that end
with arrows represent? Carpentry and Building Construction -
Page 45
