CDX - Safety and Foundation
Pretest, Chapters 1-2 fully
solved & updated (latest
version)
Henry Ford's _____ approach made assembly much more efficient, increasing
the number of vehicles that could be built in a shift and thereby lowering
production costs. - answer Assembly line
Tech A says that the production of vehicles today requires a mix of robotic
and human assembly. Tech B says that most of the parts on a vehicle are
preassembled into unit assemblies before they reach the assembly line. Who
is correct? - answer Both A and B
Heavy line technicians must be able to research service information and use
the information to help determine the cause of the problem and make the
appropriate repairs. - answer True
Which of the following can be considered a franchise? - answer Goodyear,
AAMCO, Jiffy Lube
Traditionally, a coupe has two standard seats in front, and possibly two
smaller seats behind. - answer True
A _____ is an underlying supporting structure for vehicles. - answer Chassis
Which of the following typically happens when cranking a gasoline engine
that uses a computer control engine management system? - answer Engine
sensors are monitored; timing is adjusted; injectors are adjusted
,The drive type that is becoming increasingly popular is all-wheel drive
(AWD), with all four wheels driven by the engine all the time. - answer True.
Which of the following is NOT a common angle between the banks of
cylinders in an engine configuration? - answer 25 degrees
Axles come in two configurations: _____. - answer Live axle and dead axle
Technician A states that the transfer case controls the drive to the front and
rear axles. Technician B states that transfer cases always allow the driver to
select 2WD or 4WD. Who is correct? - answer Tech A
Tech A says that both OSHA and the EPA can inspect facilities for violations.
Tech B says that a shop safety rule does not have to be reviewed once put in
place. Who is correct? - answer Tech A
The best way to get rid of exhaust gases is in a soundproof room. - answer
False
When disposing of used liquids: - answer Petroleum products can be mixed
together.
Which of the following should be inspected during a shop safety inspection? -
answer Faulty or unsafe equipment or tools; clutter, spills, unsafe shop
practices; items blocking emergency exits or walkways
Disposable dusk masks should not be used when working around asbestos
dust for all of the following reasons EXCEPT: - answer Asbestos dust is
harmless.
The most common type of eye protection is a _____, which must be marked
with "Z87.1" on the lens and frame. - answer Pair of safety glasses.
, Which of the following is NOT a question you should ask yourself as you
prepare to be as safe as possible? - answer How can I finish this task as fast
as possible?
If a foreign object is in the eye, irrigate from the nose side of the eye toward
the outside to avoid flushing material into the other eye. - answer True
The owner's manual contains all of the following details EXCEPT: - answer
engine removal procedures.
Before working on a vehicle, it is good practice to check whether a TSB has
been issued for that vehicle and type of fault or repair. - answer True
Labor guides are only available in print. - answer False
To use a parts program, you need to have a _____ understanding of how to
start and use a computer. - answer Basic
The _____ label lists a diagram of the serpentine belt routing for the engine
accessories. - answer Belt routing
Some tools are _____ or awkward to use, so seek assistance if required and
use correct manual handling techniques when using tools. - answer Heavy
Technician A says that lockout/tag-out is a safety procedure for a safe
working environment. Technician B says that lockout is designed to secure a
vehicle after all work on it has been completed. Who is correct? - answer
Technician A
Specialized manufacturer tools are shared by everyone in the shop.
Technician A says that it is critical that they are inspected for damage.
Pretest, Chapters 1-2 fully
solved & updated (latest
version)
Henry Ford's _____ approach made assembly much more efficient, increasing
the number of vehicles that could be built in a shift and thereby lowering
production costs. - answer Assembly line
Tech A says that the production of vehicles today requires a mix of robotic
and human assembly. Tech B says that most of the parts on a vehicle are
preassembled into unit assemblies before they reach the assembly line. Who
is correct? - answer Both A and B
Heavy line technicians must be able to research service information and use
the information to help determine the cause of the problem and make the
appropriate repairs. - answer True
Which of the following can be considered a franchise? - answer Goodyear,
AAMCO, Jiffy Lube
Traditionally, a coupe has two standard seats in front, and possibly two
smaller seats behind. - answer True
A _____ is an underlying supporting structure for vehicles. - answer Chassis
Which of the following typically happens when cranking a gasoline engine
that uses a computer control engine management system? - answer Engine
sensors are monitored; timing is adjusted; injectors are adjusted
,The drive type that is becoming increasingly popular is all-wheel drive
(AWD), with all four wheels driven by the engine all the time. - answer True.
Which of the following is NOT a common angle between the banks of
cylinders in an engine configuration? - answer 25 degrees
Axles come in two configurations: _____. - answer Live axle and dead axle
Technician A states that the transfer case controls the drive to the front and
rear axles. Technician B states that transfer cases always allow the driver to
select 2WD or 4WD. Who is correct? - answer Tech A
Tech A says that both OSHA and the EPA can inspect facilities for violations.
Tech B says that a shop safety rule does not have to be reviewed once put in
place. Who is correct? - answer Tech A
The best way to get rid of exhaust gases is in a soundproof room. - answer
False
When disposing of used liquids: - answer Petroleum products can be mixed
together.
Which of the following should be inspected during a shop safety inspection? -
answer Faulty or unsafe equipment or tools; clutter, spills, unsafe shop
practices; items blocking emergency exits or walkways
Disposable dusk masks should not be used when working around asbestos
dust for all of the following reasons EXCEPT: - answer Asbestos dust is
harmless.
The most common type of eye protection is a _____, which must be marked
with "Z87.1" on the lens and frame. - answer Pair of safety glasses.
, Which of the following is NOT a question you should ask yourself as you
prepare to be as safe as possible? - answer How can I finish this task as fast
as possible?
If a foreign object is in the eye, irrigate from the nose side of the eye toward
the outside to avoid flushing material into the other eye. - answer True
The owner's manual contains all of the following details EXCEPT: - answer
engine removal procedures.
Before working on a vehicle, it is good practice to check whether a TSB has
been issued for that vehicle and type of fault or repair. - answer True
Labor guides are only available in print. - answer False
To use a parts program, you need to have a _____ understanding of how to
start and use a computer. - answer Basic
The _____ label lists a diagram of the serpentine belt routing for the engine
accessories. - answer Belt routing
Some tools are _____ or awkward to use, so seek assistance if required and
use correct manual handling techniques when using tools. - answer Heavy
Technician A says that lockout/tag-out is a safety procedure for a safe
working environment. Technician B says that lockout is designed to secure a
vehicle after all work on it has been completed. Who is correct? - answer
Technician A
Specialized manufacturer tools are shared by everyone in the shop.
Technician A says that it is critical that they are inspected for damage.
