ARF 2006 FINAL REVIEW EXAM|| LATELY UPDATED QUESTIONS AND 100% CORRECT ANSWERS ALREADY GRADED A|| LATEST AND OMPLETE UPDATE 2025 WITH VERIFIED SOLUTIONS|| ASSURED PASS!!!

1c|cPc ac gc e


ARF 2006 FINAL REVIEW EXAM|| LATELY UPDATE
c c c c c c



D QUESTIONS AND 100% CORRECT ANSWERS ALR
c c c c c c



EADY GRADED A|| LATEST AND COMPLETE UPDAT c c c c c c



E 2025 WITH VERIFIED SOLUTIONS|| ASSURED PAS
c c c c c c



S!!!
Fairleads should never deflect the alignment of a cable more than? 3
c c c c c c c c c c c c




degrees




When installing a castle nut, start alignment with the cotter pin hole at the Minimum r
c c c c c c c c c c c c c c c




ecommended torque plus friction drag torque c c c c c




If the control stick of an aircraft with properly rigged flight controls is moved rearwar
c c c c c c c c c c c c c c


d and to the left, the right aileron will move?
c c c c c c c c c



Down and the elevator will move up
c c c c c c




The chord of a wing is measured from leadin
c c c c c c c c




g edge to trailing edge
c c c c




The acute angle formed by the chord line of a wing and the relative wind is known as t
c c c c c c c c c c c c c c c c c c


he?
Angle of Attack c c

,2c|cPc ac gc e




A tension regulator in the flight control cable system of a large all-
c c c c c c c c c c c c


metal aircraft is used primarily to
c c c c c




Retain a set tension c c c




Where is fuselage station No. 137 located?
c c c c c c




137 inches after of the zero or fixed reference line
c c c c c c c c c




Stability about the axis which runs parallel to the line of flight is referred to as? Lateral S
c c c c c c c c c c c c c c c c c




tability




Placing a piece of cloth around a stainless steel control cable and running it back and f
c c c c c c c c c c c c c c c c


orth over the length of the cable is generally a satisfactory method of inspecting for
c c c c c c c c c c c c c c




Broken strands c




If all instructions issued by the swaging tool manufacturer are followed when swagin
c c c c c c c c c c c c


g a cable terminal, the resultant swaged terminal strength should be
c c c c c c c c c c




Full rated strength of the cable
c c c c c




Where does the breakage of control cable wires occur most frequently? Breakage
c c c c c c c c c c c



usually occurs where cables pass over pulleys and through fairleads.
c c c c c c c c c c

, 3c|cPc ac gc e




What minimum distance must all pulleys and fairleads be from a turnbuckle? At l
c c c c c c c c c c c c c




east 2" c




Other than the manufacturer maintenance manual what other document could be used
c c c c c c c c c c c


cto determine the primary flight control surface deflection for an imported aircraft tha
c c c c c c c c c c c c


t is reassembled after shipment?
c c c c




Aircraft type certificate data sheetc c c c




The universal propeller protractor can be used to measure D
c c c c c c c c c




egrees of flap travel c c c




Are negative safeties allowed? No
c c c c




Cable misalignment will be evident by?
c c c c c




Excessive wear on one of the sides of the control cable pulley
c c c c c c c c c c c




What would be the indication of pulley misalignment Wear
c c c c c c c c c




on both sides of pulley
c c c c