Residential Contractor || with 100% Error-free Answers.
What are masonry exterior non-load bearing walls that are not wholly supported at each story?
correct answers Curtain Walls
Buildings shall have an attic access where attic areas exceed 30 sq feet and have a vertical height
of correct answers 30" or greater
The best piece of equipment to strip material over a long distance is a correct answers Scraper
The effect of loading uphill using a scraper is: correct answers It increases cycle time
A building slab will be 25' x 90' x 8" How many cubic yards of concrete will be needed? (Note:
assume that the grade will be perfectly level and that there will be no crown or slope in the slab
do not include waste or accessing your estimate. correct answers 56 yd
Block or stack bond is purely a _________ bond correct answers Pattern
How much do concrete tiles weigh per square? correct answers 900 lbs
For acceptance testing, multiple cylinders of concrete are test at how many days correct answers
28 days
How is drip edge installed at an eave end? correct answers under the felt
The main support under a wood deck is called a? correct answers Girder
What is the correct way to test a safety net used for fall protection? correct answers Drop test
with a 400 lb bag from the highest walking surface
How often must cranes in regular service be inspected for leakage in air or hydraulic systems?
correct answers each shift
corbel correct answers A projecting wall member used as a support for some element in the
superstructure.
Where shall the fireplace throat or damper be located? correct answers at least 8 inches above the
lintel
Lintel correct answers A horizontal beam used to span an opening.
What is the best dozer to use for landscaping? correct answers light utility dozer
Header correct answers A beam placed perpendicular to joists and to which joists are nailed in
framing for a chimney, stairway, or other opening.
, joist correct answers beam used to support floors or roofs
Soffit correct answers in interior, area of room that is lower than the rest of the ceiling
soffit (exterior) correct answers The underside of a roof overhang.
What is the maximum vertical rise between floor levels or landings for a flight of stairs? correct
answers 12 ft
What size landing shall be on each side of an exterior door? correct answers The width of each
landing shall have a minimum dimension of 36 inches in the direction of travel.
Before making a pass, what should the dozer be aligned with? correct answers Blade dump area
A cut stake is being set for the excavation of a trench using a building level (transit). The bottom
of the trench will be at elevation 94.00 feet. A rod reading of 4.70 feet is taken on a benchmark
whose elevation is 102.50 feet. The rod reading on the mark on the cut stake is 6.20 feet. What
should the cut stake be marked? correct answers 7.00
What is the minimum window opening that may be used for emergency escape and rescue on
floors above the grade floor? correct answers 4 sq ft
What is the maximum size hole that can be bored into a 2 x 4 non-load bearing wall? correct
answers 60% of the stud width
For lines rated 50 KV or below, OSHA requires a minimum clearance between the lines and any
part of a crane load of how many feet? correct answers 10'
When laying brick and all the vertical joints align, this is a correct answers stacked bond
hip jacks correct answers A rafter running between the plate and a hip rafter.
Hip Rafter correct answers Rafters laid diagonally from corner of a plate or girts to the ridge
Ventilation of a hip roof should include? correct answers inlet openings in the soffit area of the
eaves
eaves correct answers the overhang at the lower edge of a roof
Which is the proper placement of plywood when stacking on trusses? correct answers placed as
near as possible over the trusses supporting the load
A well-point system is the best method for dewatering in correct answers excavations
To identify a roof leak? correct answers Look for shingles that are worn, curled, or damaged
What are masonry exterior non-load bearing walls that are not wholly supported at each story?
correct answers Curtain Walls
Buildings shall have an attic access where attic areas exceed 30 sq feet and have a vertical height
of correct answers 30" or greater
The best piece of equipment to strip material over a long distance is a correct answers Scraper
The effect of loading uphill using a scraper is: correct answers It increases cycle time
A building slab will be 25' x 90' x 8" How many cubic yards of concrete will be needed? (Note:
assume that the grade will be perfectly level and that there will be no crown or slope in the slab
do not include waste or accessing your estimate. correct answers 56 yd
Block or stack bond is purely a _________ bond correct answers Pattern
How much do concrete tiles weigh per square? correct answers 900 lbs
For acceptance testing, multiple cylinders of concrete are test at how many days correct answers
28 days
How is drip edge installed at an eave end? correct answers under the felt
The main support under a wood deck is called a? correct answers Girder
What is the correct way to test a safety net used for fall protection? correct answers Drop test
with a 400 lb bag from the highest walking surface
How often must cranes in regular service be inspected for leakage in air or hydraulic systems?
correct answers each shift
corbel correct answers A projecting wall member used as a support for some element in the
superstructure.
Where shall the fireplace throat or damper be located? correct answers at least 8 inches above the
lintel
Lintel correct answers A horizontal beam used to span an opening.
What is the best dozer to use for landscaping? correct answers light utility dozer
Header correct answers A beam placed perpendicular to joists and to which joists are nailed in
framing for a chimney, stairway, or other opening.
, joist correct answers beam used to support floors or roofs
Soffit correct answers in interior, area of room that is lower than the rest of the ceiling
soffit (exterior) correct answers The underside of a roof overhang.
What is the maximum vertical rise between floor levels or landings for a flight of stairs? correct
answers 12 ft
What size landing shall be on each side of an exterior door? correct answers The width of each
landing shall have a minimum dimension of 36 inches in the direction of travel.
Before making a pass, what should the dozer be aligned with? correct answers Blade dump area
A cut stake is being set for the excavation of a trench using a building level (transit). The bottom
of the trench will be at elevation 94.00 feet. A rod reading of 4.70 feet is taken on a benchmark
whose elevation is 102.50 feet. The rod reading on the mark on the cut stake is 6.20 feet. What
should the cut stake be marked? correct answers 7.00
What is the minimum window opening that may be used for emergency escape and rescue on
floors above the grade floor? correct answers 4 sq ft
What is the maximum size hole that can be bored into a 2 x 4 non-load bearing wall? correct
answers 60% of the stud width
For lines rated 50 KV or below, OSHA requires a minimum clearance between the lines and any
part of a crane load of how many feet? correct answers 10'
When laying brick and all the vertical joints align, this is a correct answers stacked bond
hip jacks correct answers A rafter running between the plate and a hip rafter.
Hip Rafter correct answers Rafters laid diagonally from corner of a plate or girts to the ridge
Ventilation of a hip roof should include? correct answers inlet openings in the soffit area of the
eaves
eaves correct answers the overhang at the lower edge of a roof
Which is the proper placement of plywood when stacking on trusses? correct answers placed as
near as possible over the trusses supporting the load
A well-point system is the best method for dewatering in correct answers excavations
To identify a roof leak? correct answers Look for shingles that are worn, curled, or damaged
