SDI Firearms Inspection and
Troubleshooting (FTT 111) Exam
Questions and Answers 100% Pass
Which of the following statements are not true about safety and
ammunition? - ✔✔Always keep ammunition in the gunsmithing area
It is required to both __________________ and _____________________ once
the action is open to ensure the weapon is safe. - ✔✔Visually Check;
Physically Check
The initial function check is to be done: - ✔✔With no rounds or snap caps
Some break-action firearms are cocked when the __________ acts upon the
_____________________ and cocks the _________________. - ✔✔Lug;
Cocking Lever; Hammer
1
100% Pass Guarantee Katelyn Whitman, All Rights
,T/F: Manual Actions require the operator to use a moderate to heavy force
to close the breach. - ✔✔FALSE
Revolvers will lock at about the same time when the ____________ is in its
______________ position. - ✔✔Hammer; Cocked
Which of the following firearm types "push" the extracted round from the
chamber? - ✔✔Break Action
T/F: With a fixed ejector, you must quickly manipulate the action to ensure
the round is properly ejected. - ✔✔TRUE
Snap caps are meant to identify which of the following malfunctions? -
✔✔Failures to Extract, Eject, and Feed
Which of the following contribute to a failure to feed? - ✔✔Feeding Device;
Action Parts; Ammunition
Match the numbered step of the fire control group with its description: -
✔✔1) With snap caps in the chamber, set the safety in the "safe" position. 2)
Depress the trigger; it will not move. 3) Release the trigger and move to
"fire" position. 4) Depress the trigger again; hammer will have audible
2
100% Pass Guarantee Katelyn Whitman, All Rights
, "click" 5) Continue to depress trigger, manually cycle the action and eject
the snap cap. 6) Release trigger, click and hammer should not move. 7) Use
a nylon or rubber hammer and tap the receiver or action. 8) Set safety to
"safe" position, nothing should happen.
T/F: When a firearm equipped with a decocker is in the "safe" position, the
hammer may fall. - ✔✔TRUE
What would be the purpose to tap a pistol's external hammer with a rubber
mallet? - ✔✔To check the hammer/sear engagement
Match the type of cartridge to its proper headspace location: - ✔✔Rimfire-
Rim of the case; Belted Magnum Cartridge- Top of the belt of the case;
Centerfire Pistol Cartridge- Leading edge to the mouth; Bottleneck
Centerfire Rifle Cartridge-Datum line or near center of shoulder.
T/F: Too little headspace can result in the case expanding too much, which
may lead to an explosion in the chamber. - ✔✔FALSE
3
100% Pass Guarantee Katelyn Whitman, All Rights
Troubleshooting (FTT 111) Exam
Questions and Answers 100% Pass
Which of the following statements are not true about safety and
ammunition? - ✔✔Always keep ammunition in the gunsmithing area
It is required to both __________________ and _____________________ once
the action is open to ensure the weapon is safe. - ✔✔Visually Check;
Physically Check
The initial function check is to be done: - ✔✔With no rounds or snap caps
Some break-action firearms are cocked when the __________ acts upon the
_____________________ and cocks the _________________. - ✔✔Lug;
Cocking Lever; Hammer
1
100% Pass Guarantee Katelyn Whitman, All Rights
,T/F: Manual Actions require the operator to use a moderate to heavy force
to close the breach. - ✔✔FALSE
Revolvers will lock at about the same time when the ____________ is in its
______________ position. - ✔✔Hammer; Cocked
Which of the following firearm types "push" the extracted round from the
chamber? - ✔✔Break Action
T/F: With a fixed ejector, you must quickly manipulate the action to ensure
the round is properly ejected. - ✔✔TRUE
Snap caps are meant to identify which of the following malfunctions? -
✔✔Failures to Extract, Eject, and Feed
Which of the following contribute to a failure to feed? - ✔✔Feeding Device;
Action Parts; Ammunition
Match the numbered step of the fire control group with its description: -
✔✔1) With snap caps in the chamber, set the safety in the "safe" position. 2)
Depress the trigger; it will not move. 3) Release the trigger and move to
"fire" position. 4) Depress the trigger again; hammer will have audible
2
100% Pass Guarantee Katelyn Whitman, All Rights
, "click" 5) Continue to depress trigger, manually cycle the action and eject
the snap cap. 6) Release trigger, click and hammer should not move. 7) Use
a nylon or rubber hammer and tap the receiver or action. 8) Set safety to
"safe" position, nothing should happen.
T/F: When a firearm equipped with a decocker is in the "safe" position, the
hammer may fall. - ✔✔TRUE
What would be the purpose to tap a pistol's external hammer with a rubber
mallet? - ✔✔To check the hammer/sear engagement
Match the type of cartridge to its proper headspace location: - ✔✔Rimfire-
Rim of the case; Belted Magnum Cartridge- Top of the belt of the case;
Centerfire Pistol Cartridge- Leading edge to the mouth; Bottleneck
Centerfire Rifle Cartridge-Datum line or near center of shoulder.
T/F: Too little headspace can result in the case expanding too much, which
may lead to an explosion in the chamber. - ✔✔FALSE
3
100% Pass Guarantee Katelyn Whitman, All Rights
