MSSC - Quality Practices and Measurement
ACTUAL Exam Questions and CORRECT
Answers
In
manufacturing, a blueprint is also called what? - CORRECT ANSWER - A technical
drawing
An isometric drawing is a type of ___________. - CORRECT ANSWER - Pictorial
drawing
Which of the following is NOT used in the glass box method? - CORRECT ANSWER -
Rotate object in glass box.
Which of these requires a computer? - CORRECT ANSWER - CAD
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - stock size
The three standard views of an object are __________. - CORRECT ANSWER - Top,
front, right side
Engineers sometimes use a ________ to measure angles on a drawing. - CORRECT
ANSWER - protractor
The holes to be drilled in the part are represented by - CORRECT ANSWER - Dashed
lines
What is the order of precedence of lines in a drawing? - CORRECT ANSWER - Object,
hidden, center
, The number of views in a drawing ________. - CORRECT ANSWER - Is the fewest
number that shows all of the features and dimensions.
There are 60 minutes of arc in one _______. - CORRECT ANSWER - Degree
Dimensions are used to specify the __________ and location of the features of an object. -
CORRECT ANSWER - Size
Which of the following is NOT one of the six rules for dimensioning an object? - CORRECT
ANSWER - Dimension hidden lines
Which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension line.
A _________ dimension is described in inches per foot. - CORRECT ANSWER - Shaft
taper
The part of a drawing that indicates that the drawing has the most up to date information on it is
_______. - CORRECT ANSWER - Drawing revision level
If a feature on a drawing is drawn 3 inches long and the scale is 1:4, what is the actual dimension
on the object? - CORRECT ANSWER - 12 inches
Where would you look in a title block to see if there has been changes? - CORRECT
ANSWER - Revision number.
To establish on a drawing that 1/4 inch equals 1 inch, the designer would write _________. -
CORRECT ANSWER - 1/4=1
ACTUAL Exam Questions and CORRECT
Answers
In
manufacturing, a blueprint is also called what? - CORRECT ANSWER - A technical
drawing
An isometric drawing is a type of ___________. - CORRECT ANSWER - Pictorial
drawing
Which of the following is NOT used in the glass box method? - CORRECT ANSWER -
Rotate object in glass box.
Which of these requires a computer? - CORRECT ANSWER - CAD
The dimensions of raw material supplied by metal suppliers are described by the __________. -
CORRECT ANSWER - stock size
The three standard views of an object are __________. - CORRECT ANSWER - Top,
front, right side
Engineers sometimes use a ________ to measure angles on a drawing. - CORRECT
ANSWER - protractor
The holes to be drilled in the part are represented by - CORRECT ANSWER - Dashed
lines
What is the order of precedence of lines in a drawing? - CORRECT ANSWER - Object,
hidden, center
, The number of views in a drawing ________. - CORRECT ANSWER - Is the fewest
number that shows all of the features and dimensions.
There are 60 minutes of arc in one _______. - CORRECT ANSWER - Degree
Dimensions are used to specify the __________ and location of the features of an object. -
CORRECT ANSWER - Size
Which of the following is NOT one of the six rules for dimensioning an object? - CORRECT
ANSWER - Dimension hidden lines
Which type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER - Dimension line.
A _________ dimension is described in inches per foot. - CORRECT ANSWER - Shaft
taper
The part of a drawing that indicates that the drawing has the most up to date information on it is
_______. - CORRECT ANSWER - Drawing revision level
If a feature on a drawing is drawn 3 inches long and the scale is 1:4, what is the actual dimension
on the object? - CORRECT ANSWER - 12 inches
Where would you look in a title block to see if there has been changes? - CORRECT
ANSWER - Revision number.
To establish on a drawing that 1/4 inch equals 1 inch, the designer would write _________. -
CORRECT ANSWER - 1/4=1
