The process of zeroing the probe using a part that is a precise length is
known as - ANSWER Mastering
the two outside jaws of a ____ are only used to measure the outside
dimensions of parts - ANSWER B and c
If the length of a part is 5.000 inches and the reading could be as much
as 5.002 or as little as 4.998, the accuracy is said to be - ANSWER
Plus or minus 0.002
A common fractional inch rule graduation is in __________. - ANSWER
32nds
The error occurs when the measurement we think we see is not the
measurement being indicated by the instrument - ANSWER
Observational
one inch is equal to - ANSWER 25.4 mm
The conversion of 3-3/8 inches to decimal inches is - ANSWER 3.375
inches
A scale typically found on a ta3.375 inchespe measure - ANSWER
1/16
The first step in dimensional measuring is to align the end of the rule
where the zero is located with one edge of the dimension you want to
measure. This edge is called the - ANSWER Reference point
A common scale on a machinist rule is - ANSWER 150mm
, A common decimal inch rule graduation is in __________. - ANSWER
All of the above
Resolution is sometimes called ______. - ANSWER discrimination
dim - ANSWER A and C
Two systems for dimensional measurement used in manufacturing are
the SI metric system and the - ANSWER Us customary system
A tape measure is used - ANSWER A and B
To read a micrometer, your first read the - ANSWER Sleeve scale
The accuracy of a _________is that measurements can be read quicker
than with other percussion measuring devices - ANSWER Digital
caliper
The typical accuracy of an outside micrometer with a vernier scale is -
ANSWER 0.0001 inches - 0.0004 inches
The micrometer is - ANSWER the most accurate of all hand held
devices
A precision measuring tool is a device that will allow to make a
measurement to a finer degree than what can be seen by the human
eye - ANSWER All of the above
The typical accuracy of a modern dial caliper is about - ANSWER 0.001
Typical graduations of a modern dail caliper is about - ANSWER 0.1
Inches
The dial indicator makes measurements using the __ method -
ANSWER indirect comparison
known as - ANSWER Mastering
the two outside jaws of a ____ are only used to measure the outside
dimensions of parts - ANSWER B and c
If the length of a part is 5.000 inches and the reading could be as much
as 5.002 or as little as 4.998, the accuracy is said to be - ANSWER
Plus or minus 0.002
A common fractional inch rule graduation is in __________. - ANSWER
32nds
The error occurs when the measurement we think we see is not the
measurement being indicated by the instrument - ANSWER
Observational
one inch is equal to - ANSWER 25.4 mm
The conversion of 3-3/8 inches to decimal inches is - ANSWER 3.375
inches
A scale typically found on a ta3.375 inchespe measure - ANSWER
1/16
The first step in dimensional measuring is to align the end of the rule
where the zero is located with one edge of the dimension you want to
measure. This edge is called the - ANSWER Reference point
A common scale on a machinist rule is - ANSWER 150mm
, A common decimal inch rule graduation is in __________. - ANSWER
All of the above
Resolution is sometimes called ______. - ANSWER discrimination
dim - ANSWER A and C
Two systems for dimensional measurement used in manufacturing are
the SI metric system and the - ANSWER Us customary system
A tape measure is used - ANSWER A and B
To read a micrometer, your first read the - ANSWER Sleeve scale
The accuracy of a _________is that measurements can be read quicker
than with other percussion measuring devices - ANSWER Digital
caliper
The typical accuracy of an outside micrometer with a vernier scale is -
ANSWER 0.0001 inches - 0.0004 inches
The micrometer is - ANSWER the most accurate of all hand held
devices
A precision measuring tool is a device that will allow to make a
measurement to a finer degree than what can be seen by the human
eye - ANSWER All of the above
The typical accuracy of a modern dial caliper is about - ANSWER 0.001
Typical graduations of a modern dail caliper is about - ANSWER 0.1
Inches
The dial indicator makes measurements using the __ method -
ANSWER indirect comparison
