Pipe Fitter Test Exam
2024
What does TE in TE-601 stand for? - ✔✔✔ANSWER-temperature element
what does B.T.U stand for? - ✔✔✔ANSWER-British Thermal Unit
what is the boiling point of water? - ✔✔✔ANSWER-212*F
What is 3.1416? - ✔✔✔ANSWER-Pi
what is the circumference of a 15" pipe? (to the nearest tenth0 - ✔✔✔ANSWER-
47"
4" in the hundredths of a foot is? - ✔✔✔ANSWER-.33
what is the take off for a 4" x 3" LR reducing 90* ell? - ✔✔✔ANSWER-6"
, on isometric drawings what does RFWN mean? - ✔✔✔ANSWER-raised face
weld neck
what does the Pi in Pi-209 stand for? - ✔✔✔ANSWER-pressure indicator
101.25' converted into inches is what? - ✔✔✔ANSWER-101'-3"
if testing the shell side of an exchanger with the flat cap removed and all the tubes
on the bottom row had a steady flow of water pouring out of them, this would
indicate: - ✔✔✔ANSWER-floating head gasket leaking
3/4" is equal to? - ✔✔✔ANSWER-6/8
the lap joint flange is usually used when_______? - ✔✔✔ANSWER-flange hold
alignment is a problem
what is the number of a square feet in the surface of a steel plate 180 inches high
and 48 inches wide? - ✔✔✔ANSWER-60 square feet
what device is installed between a control valve and the air supply header? -
✔✔✔ANSWER-regulator
what is the most common degree of bevel on a pipe to be butt welded? -
✔✔✔ANSWER-37 1/2
the three states of matter are: - ✔✔✔ANSWER-solids, liquids,and gases
2024
What does TE in TE-601 stand for? - ✔✔✔ANSWER-temperature element
what does B.T.U stand for? - ✔✔✔ANSWER-British Thermal Unit
what is the boiling point of water? - ✔✔✔ANSWER-212*F
What is 3.1416? - ✔✔✔ANSWER-Pi
what is the circumference of a 15" pipe? (to the nearest tenth0 - ✔✔✔ANSWER-
47"
4" in the hundredths of a foot is? - ✔✔✔ANSWER-.33
what is the take off for a 4" x 3" LR reducing 90* ell? - ✔✔✔ANSWER-6"
, on isometric drawings what does RFWN mean? - ✔✔✔ANSWER-raised face
weld neck
what does the Pi in Pi-209 stand for? - ✔✔✔ANSWER-pressure indicator
101.25' converted into inches is what? - ✔✔✔ANSWER-101'-3"
if testing the shell side of an exchanger with the flat cap removed and all the tubes
on the bottom row had a steady flow of water pouring out of them, this would
indicate: - ✔✔✔ANSWER-floating head gasket leaking
3/4" is equal to? - ✔✔✔ANSWER-6/8
the lap joint flange is usually used when_______? - ✔✔✔ANSWER-flange hold
alignment is a problem
what is the number of a square feet in the surface of a steel plate 180 inches high
and 48 inches wide? - ✔✔✔ANSWER-60 square feet
what device is installed between a control valve and the air supply header? -
✔✔✔ANSWER-regulator
what is the most common degree of bevel on a pipe to be butt welded? -
✔✔✔ANSWER-37 1/2
the three states of matter are: - ✔✔✔ANSWER-solids, liquids,and gases
