Dante Level 1-3 UPDATED Actual Exam Questions and CORRECT Answers

Dante Level 1-3 UPDATED Actual Exam
Questions and CORRECT Answers
Dante audio streams over WiFi networks [are _______________________]. - CORRECT
ANSWER- ✔✔not supported



The bit depth of an audio system dictates - CORRECT ANSWER- ✔✔The amplitude
resolution of each sample


Does Dante support MIDI - CORRECT ANSWER- ✔✔No. Dante only transports audio data
and does not interfere with MIDI.


Is there any advantage to using automatic IP addressing on a Dante network - CORRECT
ANSWER- ✔✔Yes. Automatic addressing ensures that devices create a working LAN.



How are device names used in Dante - CORRECT ANSWER- ✔✔Subscriptions are made
from name to name


Dante works best with [______________] switches - CORRECT ANSWER- ✔✔gigabit



On a Dante network, latency is - CORRECT ANSWER- ✔✔deterministic, set per device


As sample rate is increased on a device, what other property is usually changed - CORRECT
ANSWER- ✔✔Channel count is reduced



Where do Dante settings reside? - CORRECT ANSWER- ✔✔On individual Dante devices


In the Dante Controller Routing tab, a green check mark indicates - CORRECT ANSWER-
✔✔Subscription successful


Which of the following are diagnostic features of Dante Controller? (check all that apply) -
CORRECT ANSWER- ✔✔1. Latency monitoring

,2. Clock monitoring


How does Dante interact with Energy Efficient Ethernet (EEE) switches? - CORRECT
ANSWER- ✔✔EEE switches are not recommended for use with Dante



When should fiber be used for an Ethernet connection? - CORRECT ANSWER- ✔✔When
runs over 100 meters are required.


The easiest way to get IP addresses for a functional stand-alone Dante network is for all
devices and computers to - CORRECT ANSWER- ✔✔Use the "obtain an IP Address
Automatically" setting


If a network is only used for Dante and has only one network switch, then - CORRECT
ANSWER- ✔✔The network does not require a managed switch



Does Dante require special network cabling? - CORRECT ANSWER- ✔✔Regular CAT5E or
CAT6 Ethernet cable is recommended


How are devices added to a Dante network - CORRECT ANSWER- ✔✔Devices are
automatically discovered and displayed in Dante Controller


Dante uses [_________________________] switches. - CORRECT ANSWER- ✔✔standard


How are devices restored to a Dante network after power cycle - CORRECT ANSWER-
✔✔Devices and connections are automatically restored



What does the Dante Clock Master do - CORRECT ANSWER- ✔✔Provides synchronization
for all Dante devices on the network


Does a Dante network require special configuration for clocking - CORRECT ANSWER-
✔✔No. A Clock Master is always automatically elected by Dante

, A[______________] network topology is a best practice for Dante. - CORRECT ANSWER-
✔✔star



What is latency - CORRECT ANSWER- ✔✔Latency is the audio signal delay in any audio
system.


Dante transmitters are sources. Dante receivers are [______________________]. -
CORRECT ANSWER- ✔✔destinations



The names of devices and channels in Dante are - CORRECT ANSWER- ✔✔User-definable
and remembered by devices.


The default Dante latency of 1 millisecond is - CORRECT ANSWER- ✔✔very low and
suitable for the majority of applications


What are the steps to delete a subscription in Dante Controller? (drag to put steps in the
correct order) - CORRECT ANSWER- ✔✔1. Open both transmitter and receiver to expose
channels
2. Click green checkmark at intersection of channels you wish to unsubscribe
3. Wait for green checkmark to disappear


Audio sent over a Dante network is - CORRECT ANSWER- ✔✔uncompressed, bit-perfect


Dante is an example of [_____________________________]. - CORRECT ANSWER-
✔✔an audio over IP (AoIP) solution


What are the steps to create a subscription in Dante Controller? (drag to put steps in the
correct order) - CORRECT ANSWER- ✔✔1. Open the transmitter and receiver to expose
channels of each
2. Click at the intersection of the two channels you wish to connect
3. Wait for green check mark to appear