10/4/24, 9:45 PM
Scheduled maintenance: October 5, 2024 from 07:00 AM to 09:00 AM
cdt comprehensive exam with 100% sure answers
Jeremiah
Terms in this set (98)
Overjet is defined as horizontal overlap.
What is the MOST likely cause for breaking undercuts were not removed before the cast was poured
a denture reline when removing the cast
Distoclusion describes a _______________ class II
occlusion
The rear most, upper most, midmost centric relation
position of the mandible in the articular
fossa is
The bilateral curve in which molars are set the Curve of Wilson
is called
What is the process of replacing all palatal rebasing
acrylic without disturbing existing denture
teeth?
What is the MOST likely cause for porosity the curing temperature was too high or the flask was underpacked
after processing and deflasking a denture?
An articulator that has adjustable but semi-adjustable articulator.
straight lateral and protrusive guidance is
called a
Wax festooning is the process of anatomically waxing the denture
anatomically waxing the denture the central fossa of the maxillary first molar
Mutually protected occlusion has posterior centric
contacts in
During denture flask wax elimination, the wax to melt and soak into the mold
immersion in the boilout tank for too much
cdt comprehensive exam
time may result in what outcome?
1/6
, 10/4/24, 9:45 PM
In Class I centric occlusion, the maxillary the facio-incisal edge of mandibular anterior teeth
anterior teeth occlude with
The __ is where the two centrals line up midline
and is marked by the dentist
The mesiobuccal cusp of the maxillary first class I
molar is in alignment with the mesiobuccal
groove of the mandibular first molar in
what type of occlusion?
What is the process used to resurface the relining
tissue side of a denture with new base
material for a better fit?
Monomer is a liquid for mixing methyl methacrylate/acrylic.
The mandibular second premolar contacts maxillary first and second premolars.
the
Which of the following is found on the tuberosity
maxilla?
According to cusp-fossa theory, cusps tips cusp tips do not actually occlude with opposing dentition
will not wear away because
The Curve of Spee is the anterior-posterior curvature of the occlusal surfaces of mandibular teeth.
What is the proper order or operations box impression, trim cast, cut notches, blockout undercuts
after receiving a denture back from the
dentist with impression material on the
tissue surface?
Polymerization of the denture means curing the denture base
The rear most, upper most, midmost centric relation
position of the mandible in the articular
fossa is
When finishing complete dentures, what directly to the object being polished
should the pumice be applied to?
Which statement best describes the Movements occur bilaterally simultaneously and in the same direction
movements in the temporomandibular joint
during centric occlusion, protrusion and
retrusion?
What is the MOST important reason to avoid loss of surface detail.
allow the gypsum cast to fully set?
Monomer is a liquid for mixing methyl methacrylate/acrylic.
The mandibular second premolar contacts maxillary first and second premolars.
the
The mesiobuccal cusp of the maxillary first class I
molar is in alignment with the mesiobuccal
groove of the mandibular first molar in
what type of occlusion?
Where are the synovial cavities located? as part of the TMJ
What is the MOST likely cause for porosity the curing temperature was too high or the flask was underpacked
after processing and deflasking a denture?
A non-arcon articulator is one which has the condyles on the upper member.
2/6
Scheduled maintenance: October 5, 2024 from 07:00 AM to 09:00 AM
cdt comprehensive exam with 100% sure answers
Jeremiah
Terms in this set (98)
Overjet is defined as horizontal overlap.
What is the MOST likely cause for breaking undercuts were not removed before the cast was poured
a denture reline when removing the cast
Distoclusion describes a _______________ class II
occlusion
The rear most, upper most, midmost centric relation
position of the mandible in the articular
fossa is
The bilateral curve in which molars are set the Curve of Wilson
is called
What is the process of replacing all palatal rebasing
acrylic without disturbing existing denture
teeth?
What is the MOST likely cause for porosity the curing temperature was too high or the flask was underpacked
after processing and deflasking a denture?
An articulator that has adjustable but semi-adjustable articulator.
straight lateral and protrusive guidance is
called a
Wax festooning is the process of anatomically waxing the denture
anatomically waxing the denture the central fossa of the maxillary first molar
Mutually protected occlusion has posterior centric
contacts in
During denture flask wax elimination, the wax to melt and soak into the mold
immersion in the boilout tank for too much
cdt comprehensive exam
time may result in what outcome?
1/6
, 10/4/24, 9:45 PM
In Class I centric occlusion, the maxillary the facio-incisal edge of mandibular anterior teeth
anterior teeth occlude with
The __ is where the two centrals line up midline
and is marked by the dentist
The mesiobuccal cusp of the maxillary first class I
molar is in alignment with the mesiobuccal
groove of the mandibular first molar in
what type of occlusion?
What is the process used to resurface the relining
tissue side of a denture with new base
material for a better fit?
Monomer is a liquid for mixing methyl methacrylate/acrylic.
The mandibular second premolar contacts maxillary first and second premolars.
the
Which of the following is found on the tuberosity
maxilla?
According to cusp-fossa theory, cusps tips cusp tips do not actually occlude with opposing dentition
will not wear away because
The Curve of Spee is the anterior-posterior curvature of the occlusal surfaces of mandibular teeth.
What is the proper order or operations box impression, trim cast, cut notches, blockout undercuts
after receiving a denture back from the
dentist with impression material on the
tissue surface?
Polymerization of the denture means curing the denture base
The rear most, upper most, midmost centric relation
position of the mandible in the articular
fossa is
When finishing complete dentures, what directly to the object being polished
should the pumice be applied to?
Which statement best describes the Movements occur bilaterally simultaneously and in the same direction
movements in the temporomandibular joint
during centric occlusion, protrusion and
retrusion?
What is the MOST important reason to avoid loss of surface detail.
allow the gypsum cast to fully set?
Monomer is a liquid for mixing methyl methacrylate/acrylic.
The mandibular second premolar contacts maxillary first and second premolars.
the
The mesiobuccal cusp of the maxillary first class I
molar is in alignment with the mesiobuccal
groove of the mandibular first molar in
what type of occlusion?
Where are the synovial cavities located? as part of the TMJ
What is the MOST likely cause for porosity the curing temperature was too high or the flask was underpacked
after processing and deflasking a denture?
A non-arcon articulator is one which has the condyles on the upper member.
2/6
