NOCTI ENGINEERING PT2 EXAM
2024-2025
Which of the following symbols is used to represent the centre of a circle? -
ANSWER+
What does the third colour band of a resistor represent? - ANSWER The first and
second bands represent the resistor's numerical value, while the colour of the third
band indicates the power-of-ten multiplier. The fourth indicates tolerance. The
colour bands are always read from left to right, beginning with the side with the
band closest to the edge.
Identifying the leader in the assembly process and routinely comparing one's
procedures and outputs to the leader is known as ANSWER Performance matching.
When energised, a solenoid acts on which of the following objects: - Steel.
Which sentence accurately characterises precision alignment? - ANSWER It
repairs any flaws in the shaft.
The most crucial thing for an engineer to consider when picking a project solution
should be safety.
Some of the benefits of following these standards include healthier employees,
greater attendance and productivity, higher morale, and lower litigation risks. -
Respond to OSHA.
ANSWER International Organisations for Standardisation is an international group
of technical standards for numerous industries, aimed to encourage international
trade, engineering compliance, and, more lately, environmental consciousness.
, When establishing the level of acceptable risk in a project, an engineer should
constantly consider - A cost/risk/benefit analysis.
To comply with OSHA in the workplace, training and assistance can be provided.
A smart approach to maintaining a safe work space is to have a clean work table,
attend safety meetings, and abide by safety signage.
In performing engineering functions, ethical conduct is the duty of the individual
engineer.
Immediately report the malfunction of any piece of equipment to the safety
engineer.
The _________ code establishes standards for connecting metals using the MIG
process - ANSWER AWS
Since 1971, when _____ was established, occupational deaths have decreased by
62 percent and injuries by 42 percent - ANSWER OSHA.
When a gas cylinder is at the workstation, as a safety precaution, - At least two
inches off the flow.
Because switches can fail after opening a disconnect, the best procedure is to
ANSWER Lock and dag the disconnect.
2024-2025
Which of the following symbols is used to represent the centre of a circle? -
ANSWER+
What does the third colour band of a resistor represent? - ANSWER The first and
second bands represent the resistor's numerical value, while the colour of the third
band indicates the power-of-ten multiplier. The fourth indicates tolerance. The
colour bands are always read from left to right, beginning with the side with the
band closest to the edge.
Identifying the leader in the assembly process and routinely comparing one's
procedures and outputs to the leader is known as ANSWER Performance matching.
When energised, a solenoid acts on which of the following objects: - Steel.
Which sentence accurately characterises precision alignment? - ANSWER It
repairs any flaws in the shaft.
The most crucial thing for an engineer to consider when picking a project solution
should be safety.
Some of the benefits of following these standards include healthier employees,
greater attendance and productivity, higher morale, and lower litigation risks. -
Respond to OSHA.
ANSWER International Organisations for Standardisation is an international group
of technical standards for numerous industries, aimed to encourage international
trade, engineering compliance, and, more lately, environmental consciousness.
, When establishing the level of acceptable risk in a project, an engineer should
constantly consider - A cost/risk/benefit analysis.
To comply with OSHA in the workplace, training and assistance can be provided.
A smart approach to maintaining a safe work space is to have a clean work table,
attend safety meetings, and abide by safety signage.
In performing engineering functions, ethical conduct is the duty of the individual
engineer.
Immediately report the malfunction of any piece of equipment to the safety
engineer.
The _________ code establishes standards for connecting metals using the MIG
process - ANSWER AWS
Since 1971, when _____ was established, occupational deaths have decreased by
62 percent and injuries by 42 percent - ANSWER OSHA.
When a gas cylinder is at the workstation, as a safety precaution, - At least two
inches off the flow.
Because switches can fail after opening a disconnect, the best procedure is to
ANSWER Lock and dag the disconnect.
