©SOPHIABENNET@2024/2025 Wednesday, August 21, 2024 12:13 PM
ASE A3 Exam Study Guide with Complete Solutions
Noise: In gear, clutch disengaged (pedal to floor) - Answer✔️✔️-Pilot
bushing or bearing
Noise: Neutral, clutch disengaged (pedal to floor) - Answer✔️✔️-
Release bearing
Noise: Neutral, clutch engaged (pedal up) - Answer✔️✔️-Input shaft
bearing
Binding U-Joint will damage?? - Answer✔️✔️-Extension housing
bushing and seal
What is used to check the clearance between the shift fork and the
synchronizer sleeve? - Answer✔️✔️-A feeler guage
Warped pressure plates... - Answer✔️✔️-... should be replaced
Ring and pinion gears... - Answer✔️✔️-...should be replaced as a set
What tool is used to measure ring gear runout? - Answer✔️✔️-A dial
guage
How many times can a collapsible sleeve be tightened? - Answer✔️✔️-
Once, and must be replaced if over tightened.
What tool is used to check pinion bearing preload? - Answer✔️✔️-
Inch pound torque wrench
1
, ©SOPHIABENNET@2024/2025 Wednesday, August 21, 2024 12:13 PM
How much vacuum is required to operate a transfer case? -
Answer✔️✔️-15hg
What type of bearings require preload? - Answer✔️✔️-Tapered roller
bearings
Can a bad speed sensor affect shift pattern? - Answer✔️✔️-Yes
What is a viscous clutch designed for? - Answer✔️✔️-Compensating
for differences in axle rotation
What kind of noise will chipped gear teeth make? - Answer✔️✔️-
Growling or grinding noise
Bell housing transmission bore and the rear face should be checked
for? - Answer✔️✔️-Runout
Check runout before or after installing pressure plate cover? -
Answer✔️✔️-Before
Correct face runout by... - Answer✔️✔️-Installing shims
Symptoms of a stuck pilot bearing? - Answer✔️✔️-Clutch not
disengaging
Noise
Clutch hub damage
Mark position of flywheel in relation to... - Answer✔️✔️-Crankshaft
Whining gears can be caused by..... - Answer✔️✔️-Low fluid
2
ASE A3 Exam Study Guide with Complete Solutions
Noise: In gear, clutch disengaged (pedal to floor) - Answer✔️✔️-Pilot
bushing or bearing
Noise: Neutral, clutch disengaged (pedal to floor) - Answer✔️✔️-
Release bearing
Noise: Neutral, clutch engaged (pedal up) - Answer✔️✔️-Input shaft
bearing
Binding U-Joint will damage?? - Answer✔️✔️-Extension housing
bushing and seal
What is used to check the clearance between the shift fork and the
synchronizer sleeve? - Answer✔️✔️-A feeler guage
Warped pressure plates... - Answer✔️✔️-... should be replaced
Ring and pinion gears... - Answer✔️✔️-...should be replaced as a set
What tool is used to measure ring gear runout? - Answer✔️✔️-A dial
guage
How many times can a collapsible sleeve be tightened? - Answer✔️✔️-
Once, and must be replaced if over tightened.
What tool is used to check pinion bearing preload? - Answer✔️✔️-
Inch pound torque wrench
1
, ©SOPHIABENNET@2024/2025 Wednesday, August 21, 2024 12:13 PM
How much vacuum is required to operate a transfer case? -
Answer✔️✔️-15hg
What type of bearings require preload? - Answer✔️✔️-Tapered roller
bearings
Can a bad speed sensor affect shift pattern? - Answer✔️✔️-Yes
What is a viscous clutch designed for? - Answer✔️✔️-Compensating
for differences in axle rotation
What kind of noise will chipped gear teeth make? - Answer✔️✔️-
Growling or grinding noise
Bell housing transmission bore and the rear face should be checked
for? - Answer✔️✔️-Runout
Check runout before or after installing pressure plate cover? -
Answer✔️✔️-Before
Correct face runout by... - Answer✔️✔️-Installing shims
Symptoms of a stuck pilot bearing? - Answer✔️✔️-Clutch not
disengaging
Noise
Clutch hub damage
Mark position of flywheel in relation to... - Answer✔️✔️-Crankshaft
Whining gears can be caused by..... - Answer✔️✔️-Low fluid
2
