A.2.2 PRO DOMAIN 2: INTERFACE
CONFIGURATION QUESTIONS AND
ANSWERS WITH SOLUTIONS 2024
In this lab, you will explore the switch port status. Devices are connected to the Branch1 switch as shown
in the diagram. No other devices are connected to the switch. During your exploration, look for a line
similar to the following:
FastEthernet 0/1 is up, line protocol is up (connected)
In this lab, your task is to complete the following:
Select Branch1.
Press Enter to get started.
At the Branch1> prompt, type enable and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Questions 1-3.
At the Branch1# prompt, type config t and press Enter.
At the Branch1(config)# prompt, type interface FastEthernet0/2 and press Enter.
At the Branch1# prompt, type shutdown and press Enter.
Press Ctrl + Z.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 4.
Select SFO.
Press Enter to get started.
At the SFO> prompt, type enable and press Enter.
At the SFO# - ANSWER Select Branch1.
Press Enter to get started.
At the Branch1> prompt, type enable and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Questions 1-3.
At the Branch1# prompt, type config t and press Enter.
At the Branch1(config)# prompt, type interface FastEthernet0/2 and press Enter.
, At the Branch1# prompt, type shutdown and press Enter.
Press Ctrl + Z.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 4.
Select SFO.
Press Enter to get started.
At the SFO> prompt, type enable and press Enter.
At the SFO# prompt, type show interface and press Enter.
Answer Questions 5-6.
At the SFO# prompt, type config t and press Enter.
At the SFO(config)# prompt, type interface FastEthernet0/0 and press Enter.
At the SFO# prompt, type shutdown and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 7.
The Memphis router has CDP enabled on it. You need to find out the CDP information on which devices
are connected to the interfaces on the router.
In this lab, your task is to answer the following questions:
Which device is connected to the Memphis FastEthernet0/1 interface?
Which device is connected to the Memphis Serial0/0/1 interface?
What is the IP address of the device connected to the Memphis Serial0/0/0 interface?
What is the IP address of the device connected to the Memphis FastEthernet0/0 interface?
Which remote port connects Branch3 to the Memphis router?
Which remote port connects Miami to the Memphis router?
Which platform is running on the device connected to the S0/0/1 interface? - ANSWER Select Router.
Press Enter to get started.
At the Memphis> prompt, type enable and press Enter.
At the Memphis# proenmpt, type show cdp neighbors and press Enter.
At the Memphis# prompt, type show cdp neighbors detail and press Enter.
CONFIGURATION QUESTIONS AND
ANSWERS WITH SOLUTIONS 2024
In this lab, you will explore the switch port status. Devices are connected to the Branch1 switch as shown
in the diagram. No other devices are connected to the switch. During your exploration, look for a line
similar to the following:
FastEthernet 0/1 is up, line protocol is up (connected)
In this lab, your task is to complete the following:
Select Branch1.
Press Enter to get started.
At the Branch1> prompt, type enable and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Questions 1-3.
At the Branch1# prompt, type config t and press Enter.
At the Branch1(config)# prompt, type interface FastEthernet0/2 and press Enter.
At the Branch1# prompt, type shutdown and press Enter.
Press Ctrl + Z.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 4.
Select SFO.
Press Enter to get started.
At the SFO> prompt, type enable and press Enter.
At the SFO# - ANSWER Select Branch1.
Press Enter to get started.
At the Branch1> prompt, type enable and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Questions 1-3.
At the Branch1# prompt, type config t and press Enter.
At the Branch1(config)# prompt, type interface FastEthernet0/2 and press Enter.
, At the Branch1# prompt, type shutdown and press Enter.
Press Ctrl + Z.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 4.
Select SFO.
Press Enter to get started.
At the SFO> prompt, type enable and press Enter.
At the SFO# prompt, type show interface and press Enter.
Answer Questions 5-6.
At the SFO# prompt, type config t and press Enter.
At the SFO(config)# prompt, type interface FastEthernet0/0 and press Enter.
At the SFO# prompt, type shutdown and press Enter.
At the Branch1# prompt, type show ip interface brief and press Enter.
Answer Question 7.
The Memphis router has CDP enabled on it. You need to find out the CDP information on which devices
are connected to the interfaces on the router.
In this lab, your task is to answer the following questions:
Which device is connected to the Memphis FastEthernet0/1 interface?
Which device is connected to the Memphis Serial0/0/1 interface?
What is the IP address of the device connected to the Memphis Serial0/0/0 interface?
What is the IP address of the device connected to the Memphis FastEthernet0/0 interface?
Which remote port connects Branch3 to the Memphis router?
Which remote port connects Miami to the Memphis router?
Which platform is running on the device connected to the S0/0/1 interface? - ANSWER Select Router.
Press Enter to get started.
At the Memphis> prompt, type enable and press Enter.
At the Memphis# proenmpt, type show cdp neighbors and press Enter.
At the Memphis# prompt, type show cdp neighbors detail and press Enter.
