OSHA 10 Hour Construction Test Answer Key FALL
HAZARDS || with Errorless Solutions 100%.
C. Both A and B are correct (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 1. OSHA requires fall
protection at different heights for construction and general industry however, regardless of the
fall distance, which of the following is most
A. Fall protection must be provided when working over dangerous equipment
B. Fall protection must be provided when working over dangerous machinery
C. Both A and B are correct
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
A. It is determined to have strength and structural integrity to support intended loads (correct
answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 2. Employees must not work on
scaffold surfaces until:
A. It is determined to have strength and structural integrity to support intended loads
B. OSHA has visited the site and inspected the scaffold
C. The surface is completely dry
D. All of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
E. All the above (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 3. From your choices below,
what would you consider to be a "major" fall hazard in construction?
A. Roof edges and floor openings
B. Steel erection
C. Improper scaffold construction
D. Unsafe use of portable ladders
E. All the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Never (correct answer)
, Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 4. Climbing on the cross braces
of scaffolds is allowed:
A. During the assembly of the scaffold
B. When conditions are dry and the climbing can be done safely
C. Never
D. When authorized by the supervisor
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Removed immediately from service (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 5. If there are defects found
during the inspection of personal fall protection equipment, or if the equipment has been used in
an arrest, it must be:
A. Fixed on the spot and tested by twisting the fabric or rope and looking for stress
B. Turned in at the end of the shift
C. Removed immediately from service
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Roofs (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 6. More than 33% of fatalities
in construction are from a combination of falls from:
A. Slips and slides
B. Tripping over electrical wires and electrical installations
C. Roofs
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
E. All the above (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 7. Examples of fall hazards that
have resulted in deaths on the jobsite include:
A. Falls to the ground or lower levels
B. Falls through existing floor or roof openings
C. Falls through the floor or roof surface
D. Falls on the same level
E. All the above
HAZARDS || with Errorless Solutions 100%.
C. Both A and B are correct (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 1. OSHA requires fall
protection at different heights for construction and general industry however, regardless of the
fall distance, which of the following is most
A. Fall protection must be provided when working over dangerous equipment
B. Fall protection must be provided when working over dangerous machinery
C. Both A and B are correct
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
A. It is determined to have strength and structural integrity to support intended loads (correct
answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 2. Employees must not work on
scaffold surfaces until:
A. It is determined to have strength and structural integrity to support intended loads
B. OSHA has visited the site and inspected the scaffold
C. The surface is completely dry
D. All of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
E. All the above (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 3. From your choices below,
what would you consider to be a "major" fall hazard in construction?
A. Roof edges and floor openings
B. Steel erection
C. Improper scaffold construction
D. Unsafe use of portable ladders
E. All the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Never (correct answer)
, Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 4. Climbing on the cross braces
of scaffolds is allowed:
A. During the assembly of the scaffold
B. When conditions are dry and the climbing can be done safely
C. Never
D. When authorized by the supervisor
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Removed immediately from service (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 5. If there are defects found
during the inspection of personal fall protection equipment, or if the equipment has been used in
an arrest, it must be:
A. Fixed on the spot and tested by twisting the fabric or rope and looking for stress
B. Turned in at the end of the shift
C. Removed immediately from service
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
C. Roofs (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 6. More than 33% of fatalities
in construction are from a combination of falls from:
A. Slips and slides
B. Tripping over electrical wires and electrical installations
C. Roofs
D. None of the above
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr
E. All the above (correct answer)
Get OSHA 10 Exam Passed - https://rebrand.ly/clisafo10consqr 7. Examples of fall hazards that
have resulted in deaths on the jobsite include:
A. Falls to the ground or lower levels
B. Falls through existing floor or roof openings
C. Falls through the floor or roof surface
D. Falls on the same level
E. All the above
