MSSC – Safety Quality Certification Exam (Graded A+ ) Waste materials such as scrap metal in an open yard are a possible __________. - ANSWER -storm water contamination source The advantage of ISO standards is that it provides a single set of guidelines that should be followed __________. - ANSWER -
worldwide An employer is responsible for having an MSDS sheet for every chemical that __________. - ANSWER -they manufacture, sell or use The PEL (Permissible Exposure Limit ) for exposure to hazardous substances are set by __________. - ANSWER -OSHA The Department of Transportation (DOT) oversees the __________. - ANSWER -transportation of hazardous materials If a large quantity of liquid is spilled into a sanitary sewer, the worker that discovers it should __________. - ANSWER -notify their supervisor or team leader immediately so the appropriate authorities can be contacted To ensure safe transportation of hazardous materials, the EPA developed regulations jointly with the _ _________. - ANSWER -DOT If safe handling information about a chemical cannot be found on its chemical label, its __________ should be checked. - ANSWER -
MSDS The reason that grease is not recycled like oil is because __________. - ANSWER -Both A and B (it is not cost efficient and it is very difficult to remove the impurities) A(n) __________ is a labeling system designed to quickly and accurately identify hazardous materials. - ANSWER -hazardous material identification system A flammable liquid falls into which category number in the DOT hazardous material identification system? - ANSWER -3 One of the simplest, but slowest methods of recycling oil is __________. - ANSWER -gravity separation The red diamond on the NFPA identific ation label represents the __________. - ANSWER -flammability level Hazardous materials being shipped internationally are give a four -
digit number preceded by the letters __________ to identify the material being shipped. - ANSWER -UN (United Nations) The first step in safely handling hazardous chemicals is __________. - ANSWER -to know the hazards about the chemical you are handling Hazardous materials of different types __________. - ANSWER -
should be stored separately In the United States, the __________ requires placards representing the classification of hazards on board a truck transporting hazardous materials. - ANSWER -Department of Transportation A well ventilated area designed for storage is the best place to store __________. - ANSWER -flammable ma terials Safety guidelines do not permit __________ to be removed by unauthorized personnel. - ANSWER -Asbestos __________ should not be placed near an ignition source because it is explosive. - ANSWER -Propane Regulations must always be followed when clea ning up __________. - ANSWER -small amounts of asbestos The amount of exposure to a chemical without the unreasonable risk of injury is listed on the MSDS as __________. - ANSWER -TLV (Threshold Limit Value) One of the best ways to learn how to operate an unfamiliar machine is to __________. - ANSWER -observe an experienced operator Machine guards that require the operator to be able to see the process should be made from __________ to protect the worker in case it breaks. - ANSWER -safety glass When using pneumatic tools __________. - ANSWER -do not use compressed air to clean clothing or skin While using a cutting tool, always __________. - ANSWER -cut away from the body
worldwide An employer is responsible for having an MSDS sheet for every chemical that __________. - ANSWER -they manufacture, sell or use The PEL (Permissible Exposure Limit ) for exposure to hazardous substances are set by __________. - ANSWER -OSHA The Department of Transportation (DOT) oversees the __________. - ANSWER -transportation of hazardous materials If a large quantity of liquid is spilled into a sanitary sewer, the worker that discovers it should __________. - ANSWER -notify their supervisor or team leader immediately so the appropriate authorities can be contacted To ensure safe transportation of hazardous materials, the EPA developed regulations jointly with the _ _________. - ANSWER -DOT If safe handling information about a chemical cannot be found on its chemical label, its __________ should be checked. - ANSWER -
MSDS The reason that grease is not recycled like oil is because __________. - ANSWER -Both A and B (it is not cost efficient and it is very difficult to remove the impurities) A(n) __________ is a labeling system designed to quickly and accurately identify hazardous materials. - ANSWER -hazardous material identification system A flammable liquid falls into which category number in the DOT hazardous material identification system? - ANSWER -3 One of the simplest, but slowest methods of recycling oil is __________. - ANSWER -gravity separation The red diamond on the NFPA identific ation label represents the __________. - ANSWER -flammability level Hazardous materials being shipped internationally are give a four -
digit number preceded by the letters __________ to identify the material being shipped. - ANSWER -UN (United Nations) The first step in safely handling hazardous chemicals is __________. - ANSWER -to know the hazards about the chemical you are handling Hazardous materials of different types __________. - ANSWER -
should be stored separately In the United States, the __________ requires placards representing the classification of hazards on board a truck transporting hazardous materials. - ANSWER -Department of Transportation A well ventilated area designed for storage is the best place to store __________. - ANSWER -flammable ma terials Safety guidelines do not permit __________ to be removed by unauthorized personnel. - ANSWER -Asbestos __________ should not be placed near an ignition source because it is explosive. - ANSWER -Propane Regulations must always be followed when clea ning up __________. - ANSWER -small amounts of asbestos The amount of exposure to a chemical without the unreasonable risk of injury is listed on the MSDS as __________. - ANSWER -TLV (Threshold Limit Value) One of the best ways to learn how to operate an unfamiliar machine is to __________. - ANSWER -observe an experienced operator Machine guards that require the operator to be able to see the process should be made from __________ to protect the worker in case it breaks. - ANSWER -safety glass When using pneumatic tools __________. - ANSWER -do not use compressed air to clean clothing or skin While using a cutting tool, always __________. - ANSWER -cut away from the body
