PA state inspection categories test Accurate Answers 2024

How should Suspension components be maintained? -ANSWERS every suspension component shall be in safe operating condition how should steering components be maintained? -ANSWERS the steering component should be in safe operating conditions the steering wheel shall have a minimum outside diameter of ?? -ANSWERS 13 inches a passenger car manufactured after June 30, 1967 and designated as a 1968 or later model shall be equipped with what? -ANSWERS service brake system with rupture failure design that doesn't not result in complete brake loss brake lines shall be approved for use as -ANSWERS brake lines what shall a vehicle specified in this chapter be equipped with? -ANSWERS parking brake what should a parking brake be adequate to hold the vehicle on? -ANSWERS ice or snow on a 20% grade a radial ply tire shall not be used on? -ANSWERS the same axle as a belted or bias tire different types of tires -ANSWERS different types of tires shall not be used on the same axle unless in the event of an emergency Non-Pneumatic tires -ANSWERS only if originally equipped by the manufacturer and or an antique vehicle ice grips or studs -ANSWERS may not be equipped if they have projections greater than 2/32nds tires and rims -ANSWERS must meet or beat manufacturer specs spacers can be no thicker than -ANSWERS 1/4 inch what head lamp system should your vehicle be equipped with -ANSWERS two or four head lamp system low beam candle watts must be brighter than? -ANSWERS 7500 high beam candle watts cannot be less than? -ANSWERS 10,000 total candle wattage cannot exceed? -ANSWERS 150,000 watts lamps must be visible from how far? -ANSWERS 500 feet brake lamps must be visible from -ANSWERS 100 feet how many flashes should turn signals be per minute? -ANSWERS 60-120 tag lights should be visible from -ANSWERS 50 feet window tint must not pass which line -ANSWERS AS1 line all mirrors must be what? -ANSWERS crack free, hold position they are fixed to and be able to see 200 feet how many cycles per minute do wipers make -ANSWERS 45 cycles per minute how far should a horn be heard from? -ANSWERS 200 feet fender flares must not exceed? -ANSWERS 3 inches car bumper when measured from lowest point are how high off the ground? -ANSWERS 16-20 inches no higher no lower how high are truck bumpers when measured from the lowest point? -ANSWERS 16-30 inches no higher no lower two adjacent tread depths of _______ or less fails a car -ANSWERS 2/32nds two adjacent tread depths of _______ or less fails a truck -ANSWERS 4/32nds what type of construction should your head lamps be in a two lamp construction? -ANSWERS type 2 what type of construction should your head lamps be in a four lamp construction? -ANSWERS two lamps shall be type 2 construction and two lamps shall be of type 1 one contruction what kind of dimming switch must be installed? -ANSWERS manual dimming switch, and auto can be installed in addition to the manual switch stop lamps hazards and warning lights must be visible from? -ANSWERS 100feet lamps shall be what? -ANSWERS properly fastened, in accordance with tables 2-4, unobstructed, ornamental lamps -ANSWERS a no go unless they are emergency lights back up lamps cannot be? -ANSWERS on when in forward motion registration plate lamp must be visible from -ANSWERS 50 feet fog lamps cannot be substituted for? -ANSWERS head lamps auxiliary driving lamp dimensions -ANSWERS 20in apart from center to center not more than 42 inches above level surface auxiliary driving lamps and fog lamps shall be aimed? -ANSWERS in straight ahead position not above horizontal centerline of lamp at 25 feet may on have how many auxiliary driving lamps? -ANSWERS a pair auxiliary lamps shall not be used on? -ANSWERS snow plows, blocking a primary light, substituting head lights. snow plows lamps are wired how? -ANSWERS through a double throw switch so they can be operated separately from head lights roof or roll bar lights installed shall not be? -ANSWERS used on a highway, and are covered at all times antique vehicles equipped with limited OE lighting are? -ANSWERS exempt truck weight stickers are located where? -ANSWERS lower left Out of state inspection stickers are located where? -ANSWERS lower left or right of windshield toll stickers are located where -ANSWERS left rear window obstructions are what? -ANSWERS tint past AS1 line, lettering anywhere, posters signs stickers, things hanging from the mirror. vehicle must be equipped with at least how many rear view mirrors? -ANSWERS one mirrors shall be free of? -ANSWERS obstructions rear views mirrors must have a minimum surface space of? -ANSWERS 19.5 square inches at least a 4x5 mirror windshield defroster shall be? -ANSWERS im working conditions windshield washers shall be installed in vehicles produced after? -ANSWERS 1968 model year wipers shall be in -ANSWERS good working order not tattered cracked or falling apart fuel systems shall be -ANSWERS leak proof, intact and fastened properly accelerator control shall -ANSWERS be capable of returning to idle speedometer have to? -ANSWERS work odometers have to -ANSWERS work unless its over 25 years old exhaust systems -ANSWERS all components must be present and meet or exceed manufacturer specs and not be excessively loud, have a heat shield. fenders should not be? -ANSWERS in contact with the wheels hood and hood latches should -ANSWERS be present, cover the engine, be free of holes and lock on latch protruding objects -ANSWERS shall not be glass, metal or plastic dislocated or dislodged from the vehicle doors must be? -ANSWERS present, function as to open and close securely, unless modified to have no roof or side, tailgates can be removed if there is a net wooden plant or optional equipment present to secure contents vehicle frame shall be? -ANSWERS solid motor mounts shall be -ANSWERS not broken, crack free or missing flooring should be -ANSWERS able to support occupants hole free. bumpers -ANSWERS shall be securely attached, meet or exceed oe specs, and can be a wood plank affixed to a steel bumper seat shall be -ANSWERS have no springs protruding and adjusting mechanism must work safety belts should be -ANSWERS equipped, not frayed, and have working belt buckles