ABO PRACTICE EXAMS(QUESTIONS AND ANSWERS) LATEST

ABO PRACTICE EXAMS(QUESTIONS AND ANSWERS) LATEST If the wearer complains of the bifocal line being somewhat in his way when driving, the problem may be alleviated by decreasing the distance between pads. True or False - CORRECT ANSWER-False If the wearer complains that the glasses feel snug but still slip down the nose, one likely cause is that: A. The frame is too small B. The bridge fit is tight C. Pressure is being applied by the temple shafts anterior to the ear. D. Pressure is being applied on the very tips of the temples. - CORRECT ANSWERPressure is being applied by the temple shafts anterior to the ear If both nosepads press the nose or indent too much, what is probably not a possible cause? A. Pads too small for frame weight B. Temple spread is not even C. Pads too close together D. Temple tension too great - CORRECT ANSWER-Temple spread is not even To eliminate a gap between the lens and a metal eyewire, the best alternative is to: A. Place a strip of lens liner at a point exactly opposite the gap B. Place a strip of lens liner in the gap area C. Heat the lens in the frame and allow it to cool at room temperature D. None of the above methods are satisfactory E. All of the above methods are satisfactory - CORRECT ANSWER-Place a strip of lens liner at a point exactly opposite the gap The larger the frame difference --------- the lens shape A. Rounder B. More squared off C. Narrower D. Wider - CORRECT ANSWER-Narrower (Frame Difference=A-B) Which is the most favorable alternative to a 50/20 frame for measuring bifocal height when that particular size is not available? A. 52/18 B. 50/18 C. 48/20 D. 50/22 - CORRECT ANSWER-48/20 (would want bridge to stay the same) When the frame front is tested for four point tough, but only touches on the two temporal sides, the frame -------- A. is skewed B. has face form C. is out of coplanar alignment D. has X ing E. none of the above - CORRECT ANSWER-Has face form Which of the following errors will not be detected by a four point touch test? A. X-ing B. Excess face form C. Skewing D. All of the above can be detected using a four point touch - CORRECT ANSWERSkewing It is unnecessary to use heat in adjusting a zyl frame when: A. Bending the endpieces B. Changing the bridge area C. Bending the temple earpiece D. Changing the pantoscopic angle - CORRECT ANSWER-Changing the pantoscopic angle If you didn't adjust the eye piece on the lensometer and the power drum reads +0.25 when the target lines are clear and focused. What do you expect the true readings for this pair of glasses be? O.D. -1.75 OS +1.75 A. -1.50, +2.00 B. -1.75, +1.75 C. -1.75, +2.00 D. -1.50, +1.75 - CORRECT ANSWER--1.50, +2.00 What is the final step in fitting a frame to a patient? A. Aligning the frame vertically B. Aligning the frame horizontally C. Adjusting the pantoscopic tilt D. Adjusting the temples - CORRECT ANSWER-Adjusting the temples If the frame is crooked with the right side higher than the left, which is not a possible cause? A. The left ear is lower than the right B. The right temple is too short C. The pantoscopic tilt of the right side needs to be decreased. D. The pantoscopic tilt of the right side needs to be increased - CORRECT ANSWERThe pantoscopic tilt of the right side needs to be increased The main reason for the use of lenticular lenses for high powers would be: A. Cosmetic reasons B. They have more plus power C. They have more minus power D. They are lighter in weight E. They are less expensive - CORRECT ANSWER-They are lighter in weight A patient comes back to the optician complaining of pain behind the ears, possible cause are: A. Temple tension too great B. Uneven pressure C. Temple endpieces angled in too much D. All of the above - CORRECT ANSWER-All of the above What type of frame may be heated until it bends under its own weight? A. Zyle B. Optyl C. Nylon D. None of the above - CORRECT ANSWER-Optyl The steps for "finishing" a lens (in correct order) are: A. Centeration, Spotting, Calculation, Blocking, Edging B. Edging, Centeration, Blocking, Spotting C. Calculation, Spotting, Centeration, Blocking, Edging - CORRECT ANSWERCalculation, Spotting, Centeration, Blocking, Edging For every 2 degrees of pantoscopic tilt the optical center should be: A. Raised 0.5mm B. Raised 1mm C. Lowered 1mm D. Lowered 0.5mm - CORRECT ANSWER-Lowered 1mm Usual reading level is considered to be ------- mm below A. 6mm B. 8mm C. 11mm D. 1mm - CORRECT ANSWER-8mm The standard distance between the segments in double segment multifocals in most cases is A. 10 to 12 mm B. 13 to 14 mm C. 14 to 15 mm D. 15 to 16 mm - CORRECT ANSWER-13 to 14mm Photochronic lenses will be darkest on which day? A. Warm bright B. Cold bright C. Cloudy warm D. Cloudy cold - CORRECT ANSWER-Cold bright A Number 3 tint absorbs A. 80% of the light entering the lens B. 50% of the light entering the lens C. 60% of the light entering the lens D. 33.3% of the light entering the lens - CORRECT ANSWER-80% of the light entering the lens A customer complains that his old glasses have better visual acuity than the new glasses (same RX). What should the optician do? A. Return the customer to the refractionist B. Remake the lenses C. Check the base curve D. Put the old lenses in a new frame - CORRECT ANSWER-Check the base curve Within the first few minutes of contact with a new customer you must: A. Find out if the customer has a new prescription