CSX CONDUCTOR QUESTIONS AND ANSWERS SET
A+
✔✔Normal - ✔✔Switches and derails must be lined in the ________ position, except
whe changed for immediate movement.
✔✔Operator - ✔✔A remote control _________ is an employee who has control of
remote control locomotice or platform. (RCO)
✔✔Foreman - ✔✔A remote control operator who is in charge of a remote control crew is
called a remote control operating _______. (RCOF)
✔✔Control - ✔✔An operator ________ unit is a device through which a remotely
controlled locomotive or platform is operated.
✔✔Zone - ✔✔When activated, a designated portion of track may operate without
protection on the leading end movements. This is known as a Remote Control ______.
(RCZ)
✔✔Operator - ✔✔Before being authorized to enter an Activated Remote Control Zone
(RCZ), employees must get permission from the Remote Control ____________
Foreman.
✔✔Shove Lights, shoving - ✔✔Unless protected by ________ _________ or other
technological means, ___________ or pushing movements must be protected by a
crew member.
✔✔Conflicting, lined, road, sufficient - ✔✔After strecthing the slack, provide point
protection and make positive visual determination that there are no _________
movements, intervening switches and derails are properly _________, no intervening
______ crossings, and that there is _________ room in thetrack for the cars being
shoved.
, ✔✔RFNOCOM - ✔✔Which EOT/HTD message is not considered a failure message.
✔✔30, 2 - ✔✔When a telemetry device fails en route, you must not exceed ___ MPH, or
move on a grade of __ % or more.
✔✔6 - ✔✔Air brake cylinder piston travel on truck mounted brakes must not exceed __
inches, or it will be considered inoperative.
✔✔Cut out, set, 4 - ✔✔When you have an overheated bearing on a car, you must
______ ____ the brakes, ____ the car out ASAP, and not exceed __ MPH.
✔✔Front - ✔✔On your way into the terminal the dispatcher asks you to pick up 30
loaded hopper cars. Where do you put these in your train if your train has all empty
cars?
✔✔25 - ✔✔When handling CSX engineering equipment on your train, do not exceed
___ MPH unless otherwise instructed.
✔✔50 - ✔✔When handling air dump cars not listed in rule 4556, do not exceed ___
MPH.
✔✔50 - ✔✔What is your maximum speed when handling a loaded coal train?
✔✔Freight Train Speed - ✔✔At what speed can a locomotive consist without cars
travel?
✔✔Train Documentation - ✔✔A computer generated document consiting of some or all
of the following: Tonnage Graph, CT-168, Restricted & Special Handling report, CBI
Instructions, HAZMAT Radio WayBill form, HAZMAT handling instructions is called CSX
________ ___________.
✔✔Writing, Repeated - ✔✔A Mandatory Directive must be recorded in ___________
and must be __________.
✔✔Radio Waybill - ✔✔On what form do you write down shipping information received
orally?
✔✔NI, NT - ✔✔Which two work instruction exception codes do not require reason
codes? _ _ and _ _ .
✔✔Load, Axle - ✔✔Which two items on a tonnage graph are the most important? _____
status, and ____ count.
A+
✔✔Normal - ✔✔Switches and derails must be lined in the ________ position, except
whe changed for immediate movement.
✔✔Operator - ✔✔A remote control _________ is an employee who has control of
remote control locomotice or platform. (RCO)
✔✔Foreman - ✔✔A remote control operator who is in charge of a remote control crew is
called a remote control operating _______. (RCOF)
✔✔Control - ✔✔An operator ________ unit is a device through which a remotely
controlled locomotive or platform is operated.
✔✔Zone - ✔✔When activated, a designated portion of track may operate without
protection on the leading end movements. This is known as a Remote Control ______.
(RCZ)
✔✔Operator - ✔✔Before being authorized to enter an Activated Remote Control Zone
(RCZ), employees must get permission from the Remote Control ____________
Foreman.
✔✔Shove Lights, shoving - ✔✔Unless protected by ________ _________ or other
technological means, ___________ or pushing movements must be protected by a
crew member.
✔✔Conflicting, lined, road, sufficient - ✔✔After strecthing the slack, provide point
protection and make positive visual determination that there are no _________
movements, intervening switches and derails are properly _________, no intervening
______ crossings, and that there is _________ room in thetrack for the cars being
shoved.
, ✔✔RFNOCOM - ✔✔Which EOT/HTD message is not considered a failure message.
✔✔30, 2 - ✔✔When a telemetry device fails en route, you must not exceed ___ MPH, or
move on a grade of __ % or more.
✔✔6 - ✔✔Air brake cylinder piston travel on truck mounted brakes must not exceed __
inches, or it will be considered inoperative.
✔✔Cut out, set, 4 - ✔✔When you have an overheated bearing on a car, you must
______ ____ the brakes, ____ the car out ASAP, and not exceed __ MPH.
✔✔Front - ✔✔On your way into the terminal the dispatcher asks you to pick up 30
loaded hopper cars. Where do you put these in your train if your train has all empty
cars?
✔✔25 - ✔✔When handling CSX engineering equipment on your train, do not exceed
___ MPH unless otherwise instructed.
✔✔50 - ✔✔When handling air dump cars not listed in rule 4556, do not exceed ___
MPH.
✔✔50 - ✔✔What is your maximum speed when handling a loaded coal train?
✔✔Freight Train Speed - ✔✔At what speed can a locomotive consist without cars
travel?
✔✔Train Documentation - ✔✔A computer generated document consiting of some or all
of the following: Tonnage Graph, CT-168, Restricted & Special Handling report, CBI
Instructions, HAZMAT Radio WayBill form, HAZMAT handling instructions is called CSX
________ ___________.
✔✔Writing, Repeated - ✔✔A Mandatory Directive must be recorded in ___________
and must be __________.
✔✔Radio Waybill - ✔✔On what form do you write down shipping information received
orally?
✔✔NI, NT - ✔✔Which two work instruction exception codes do not require reason
codes? _ _ and _ _ .
✔✔Load, Axle - ✔✔Which two items on a tonnage graph are the most important? _____
status, and ____ count.
