AMTEC: ADVANCED TECHNOLOGIES COMPREHENSIVE
TEST BANK FINAL EXAM CURRENT FOR 2026/2027
PRACTICE QUESTIONS AND STUDY GUIDE COMPLETE
ACCURATE EXAM ACTUAL QUESTIONS AND CORRECT
VERIFIED ANSWERS WITH DETAILED RATIONALES
(RELIABLE SOLUTIONS) A NEW UPDATED VERSION
2026 EDITION ||JUST RELEASED |Elizabethtown
Community and Technical College
Prior to bearing installations _____________ _.
Select one:
you can select any bearing that has the same basic overall dimensions
you need to check that the bearing is the correct type and size as per the
manufacturer's specifications
you need to select a bearing that has the exact part number and
manufacturer
you can replace a roller bearing with the same size ball bearing
ANSWERS: you need to check that the bearing is the correct type and size as
per the manufacturer's specifications
,Prior to lubricating a tapered roller bearing ______________ _.
Select one:
the bearing should be cleaned by spinning the bearing with an air gun
the bearing should be cleaned in a parts cleaner
the slushing compound used to protect the bearing in storage needs not
be
removed
bearings should be wrapped in paper towels when not in use
ANSWERS: the slushing compound used to protect the bearing in
storage needs not be removed
Roller bearings can carry heavier loads due to_______________ _.
Select one:
point contact
greater line contact
angular contact
point-to-point contact
ANSWERS: greater line contact
,Taper bearings mounted with an interference fit into a housing
_______________________.
Select one:
must be heated by an induction heater
may be heated by an oven
may be cooled by a cool plate
may be cooled in a bath of alcohol cooled by dry ice
ANSWERS: may be cooled in a bath of alcohol cooled by dry ice
The key to good plain bearing performance is ______________ _.
Select one:
having the correct clearances and correct lubricant
as tight a fit as possible to minimize lubrication friction
scuffed surfaces to enhance lubrication
pre-lubrication with the correct oil viscosity
ANSWERS: having the correct clearances and correct lubricant
, The main purpose of a shaft is ______________ _.
Select one:
to transfer force and motion from one device to another
to connect one machine component to another component
to support bearing races
to increase torque values
ANSWERS: to transfer force and motion from one device to another
The most common cause of lip seal failure is ______________ _.
Select one:
damage that occurs during the handling or fitting of the seal
excessive heat
excessive lubrication
excessive vibration due to shaft misalignment
ANSWERS: damage that occurs during the handling or fitting of the seal
TEST BANK FINAL EXAM CURRENT FOR 2026/2027
PRACTICE QUESTIONS AND STUDY GUIDE COMPLETE
ACCURATE EXAM ACTUAL QUESTIONS AND CORRECT
VERIFIED ANSWERS WITH DETAILED RATIONALES
(RELIABLE SOLUTIONS) A NEW UPDATED VERSION
2026 EDITION ||JUST RELEASED |Elizabethtown
Community and Technical College
Prior to bearing installations _____________ _.
Select one:
you can select any bearing that has the same basic overall dimensions
you need to check that the bearing is the correct type and size as per the
manufacturer's specifications
you need to select a bearing that has the exact part number and
manufacturer
you can replace a roller bearing with the same size ball bearing
ANSWERS: you need to check that the bearing is the correct type and size as
per the manufacturer's specifications
,Prior to lubricating a tapered roller bearing ______________ _.
Select one:
the bearing should be cleaned by spinning the bearing with an air gun
the bearing should be cleaned in a parts cleaner
the slushing compound used to protect the bearing in storage needs not
be
removed
bearings should be wrapped in paper towels when not in use
ANSWERS: the slushing compound used to protect the bearing in
storage needs not be removed
Roller bearings can carry heavier loads due to_______________ _.
Select one:
point contact
greater line contact
angular contact
point-to-point contact
ANSWERS: greater line contact
,Taper bearings mounted with an interference fit into a housing
_______________________.
Select one:
must be heated by an induction heater
may be heated by an oven
may be cooled by a cool plate
may be cooled in a bath of alcohol cooled by dry ice
ANSWERS: may be cooled in a bath of alcohol cooled by dry ice
The key to good plain bearing performance is ______________ _.
Select one:
having the correct clearances and correct lubricant
as tight a fit as possible to minimize lubrication friction
scuffed surfaces to enhance lubrication
pre-lubrication with the correct oil viscosity
ANSWERS: having the correct clearances and correct lubricant
, The main purpose of a shaft is ______________ _.
Select one:
to transfer force and motion from one device to another
to connect one machine component to another component
to support bearing races
to increase torque values
ANSWERS: to transfer force and motion from one device to another
The most common cause of lip seal failure is ______________ _.
Select one:
damage that occurs during the handling or fitting of the seal
excessive heat
excessive lubrication
excessive vibration due to shaft misalignment
ANSWERS: damage that occurs during the handling or fitting of the seal
