MILLWRIGHT EXAM TEST | COMPLETE QUESTIONS WITH 100%
RATED EXPERT SOLUTIONS |2026 LATEST UPDATED
If the seal was not properly aligned or there is excessive wear in some bearing or shaft______
wear tracks will be the indicator. - (answer)Unusual
For removing hard to remove gasket materials found on sealing surfaces ______ is
recommended. - (answer)sharpened brass putty knife
Apprenticeship training is - (answer)Conducted on the job
Charting alignment on a graph requires a chart that is divided into thousandths of an inch
vertically for the indicator readings and into whole inches horizontally for the _______
measurements. - (answer)Distance
The orthographic drawing may contain a dash or ______ line - (answer)Hidden
In order to shoot through a test object and project an image onto a detector sheet or film
radiography used as a source of penetrating _____. - (answer)Radiation
,Which of the following task would you not perform with dividers? - (answer)Measure angles
The overspeed trip device is actuated when the turbine reaches a predetermined limit usually
_______ percent above normal full load speed - (answer)10
Positive results in an offset measurement mean that the MTBM is ______ or on the 3 o'clock
side - (answer)High
Coupling gap is set and then there is measured - (answer)Offset misalignment
In a hydraulic system movement depends on - (answer)Pressure
Fractional dimensions are used on objects ____ - (answer)Such as furniture or utility items
If the cause of the problem is not immediately understood the process of _____ is often the
procedure of choice - (answer)Elimination
When applying sealant to the sealing glands flanges keep the sealant away from the inside edges
of the flange by at least _______ inch - (answer)3/16
, A stroboscope is triggered by _______ - (answer)Transducer
The page of threaded fasteners is measured with a ______ gauge. - (answer)Thread
Liquid penetrant highlights flaws in reveals ______. - (answer)Surface cracks
The tool used to cut external threads on a boat or rod is a____ - (answer)Die
A bill of materials may include information on ______ and other reference information -
(answer)Special processes
Engaged gears always have the same ______ - (answer)Surface speed
Elevation of equipment is usually found in the - (answer)General arrangements
Inspect the police rollers in idlers for unevenness or _____ - (answer)Vibrations
RATED EXPERT SOLUTIONS |2026 LATEST UPDATED
If the seal was not properly aligned or there is excessive wear in some bearing or shaft______
wear tracks will be the indicator. - (answer)Unusual
For removing hard to remove gasket materials found on sealing surfaces ______ is
recommended. - (answer)sharpened brass putty knife
Apprenticeship training is - (answer)Conducted on the job
Charting alignment on a graph requires a chart that is divided into thousandths of an inch
vertically for the indicator readings and into whole inches horizontally for the _______
measurements. - (answer)Distance
The orthographic drawing may contain a dash or ______ line - (answer)Hidden
In order to shoot through a test object and project an image onto a detector sheet or film
radiography used as a source of penetrating _____. - (answer)Radiation
,Which of the following task would you not perform with dividers? - (answer)Measure angles
The overspeed trip device is actuated when the turbine reaches a predetermined limit usually
_______ percent above normal full load speed - (answer)10
Positive results in an offset measurement mean that the MTBM is ______ or on the 3 o'clock
side - (answer)High
Coupling gap is set and then there is measured - (answer)Offset misalignment
In a hydraulic system movement depends on - (answer)Pressure
Fractional dimensions are used on objects ____ - (answer)Such as furniture or utility items
If the cause of the problem is not immediately understood the process of _____ is often the
procedure of choice - (answer)Elimination
When applying sealant to the sealing glands flanges keep the sealant away from the inside edges
of the flange by at least _______ inch - (answer)3/16
, A stroboscope is triggered by _______ - (answer)Transducer
The page of threaded fasteners is measured with a ______ gauge. - (answer)Thread
Liquid penetrant highlights flaws in reveals ______. - (answer)Surface cracks
The tool used to cut external threads on a boat or rod is a____ - (answer)Die
A bill of materials may include information on ______ and other reference information -
(answer)Special processes
Engaged gears always have the same ______ - (answer)Surface speed
Elevation of equipment is usually found in the - (answer)General arrangements
Inspect the police rollers in idlers for unevenness or _____ - (answer)Vibrations
