Metallic Structures Part 2 UPDATED ACTUAL Questions and
CORRECT Answers
Question: 8046-1
Correct Answer: Which of the following is one advantage of HI-LOK fasteners? A-Shorter transition area
between the shank and thread. B-External counterbore at the base to accommodate material thickness.
C-Inability to be over-torqued.: C-Inability to be over-torqued.
Question: 8047
Correct Answer: The markings on the head of a Dzus fastener identify the A-body diameter, type of head,
and length of the fastener. B-body type, head diameter, and type of material. C-manufacturer and type of
material.: A-body diameter, type of head, and length of the fastener.
Question: 8048
Correct Answer: The Dzus turnlock fastener consists of a stud, grommet, and receptacle. The stud length
is measured in A-hundredths of an inch. B-tenths of an inch. C-sixteenths of an inch.: A-hundredths of an
inch.
Question: 8049
Correct Answer: The Dzus turnlock fastener consists of a stud, grommet, and receptacle. The stud
diameter is measured in A-tenths of an inch. B-hundredths of an inch. C-sixteenths of an inch.: C-sixteenths
of an inch.
Question: 8050
Correct Answer: Threaded rivets (Rivnuts) are commonly used to A-join two or more pieces of sheet
metal where shear strength is desired. B-attach parts or components with screws to sheet metal. C-join two
or more pieces of sheet metal where bearing strength is desired.- : B-attach parts or components with screws
to sheet metal.
Question: 8100
Correct Answer: Select the alternative which best describes the function of the flute section of a twist drill.
A-Provides a method for cooling oil to be delivered to the cutting surface. B-Forms the area where the drill
bit attaches to the drill motor. C-Forms the cutting edges of the drill point.: C-Forms the cutting edges of the
drill point.
Question: 8101
Correct Answer: How many MS20470 AD-4-6 rivets will be required to attach a 10" x 5" plate, using a
single row of rivets, minimum edge distance, and 4D spacing? A-56 B-54 C-52: A-56.
Question: 8104
Correct Answer: What should be the included angle of a twist drill for soft metals? A-118º B-90º C-65º:
B-90º
Question: 8105
Correct Answer: When comparing the machining techniques for stainless steel sheet material to those for
aluminum alloy sheet, it is normally considered good practice to drill the stainless steel at a A-higher speed
with less pressure applied to the drill. B-lower speed with more pressure applied to the drill. C-lower speed
CORRECT Answers
Question: 8046-1
Correct Answer: Which of the following is one advantage of HI-LOK fasteners? A-Shorter transition area
between the shank and thread. B-External counterbore at the base to accommodate material thickness.
C-Inability to be over-torqued.: C-Inability to be over-torqued.
Question: 8047
Correct Answer: The markings on the head of a Dzus fastener identify the A-body diameter, type of head,
and length of the fastener. B-body type, head diameter, and type of material. C-manufacturer and type of
material.: A-body diameter, type of head, and length of the fastener.
Question: 8048
Correct Answer: The Dzus turnlock fastener consists of a stud, grommet, and receptacle. The stud length
is measured in A-hundredths of an inch. B-tenths of an inch. C-sixteenths of an inch.: A-hundredths of an
inch.
Question: 8049
Correct Answer: The Dzus turnlock fastener consists of a stud, grommet, and receptacle. The stud
diameter is measured in A-tenths of an inch. B-hundredths of an inch. C-sixteenths of an inch.: C-sixteenths
of an inch.
Question: 8050
Correct Answer: Threaded rivets (Rivnuts) are commonly used to A-join two or more pieces of sheet
metal where shear strength is desired. B-attach parts or components with screws to sheet metal. C-join two
or more pieces of sheet metal where bearing strength is desired.- : B-attach parts or components with screws
to sheet metal.
Question: 8100
Correct Answer: Select the alternative which best describes the function of the flute section of a twist drill.
A-Provides a method for cooling oil to be delivered to the cutting surface. B-Forms the area where the drill
bit attaches to the drill motor. C-Forms the cutting edges of the drill point.: C-Forms the cutting edges of the
drill point.
Question: 8101
Correct Answer: How many MS20470 AD-4-6 rivets will be required to attach a 10" x 5" plate, using a
single row of rivets, minimum edge distance, and 4D spacing? A-56 B-54 C-52: A-56.
Question: 8104
Correct Answer: What should be the included angle of a twist drill for soft metals? A-118º B-90º C-65º:
B-90º
Question: 8105
Correct Answer: When comparing the machining techniques for stainless steel sheet material to those for
aluminum alloy sheet, it is normally considered good practice to drill the stainless steel at a A-higher speed
with less pressure applied to the drill. B-lower speed with more pressure applied to the drill. C-lower speed
