CSMLS EXAM
SAFETY MANUAL
PRACTICE QUESTIONS
VERIFIED QUESTIONS AND
ANSWERS GRADED A+
,What are the major ways to deal with risk?
a. ignore them, make employees sign non-liability contracts
b. worker's compensation
c. report to government
d. tolerate, treat, terminate or transfer the risk - CORRECT ANSWER - d. tolerate,
treat, terminate or transfer the risk
Name the 5 categories of hazards: - CORRECT ANSWER –
1. chemical
2. biological
3. physical
4. ergonomic
5. psychological
Which of the following may be useful in helping to identify laboratory hazards?
a. safety data sheets
b. inspections
c. incident reports
d. all of the above - CORRECT ANSWER - d. all of the above
Personal monitoring can be used to measure noise exposure.
a. true
b. false - CORRECT ANSWER - a. true
,Standards for all chemicals that identify allowable levels of exposure are available.
a. true
b. false - CORRECT ANSWER - b. false
Threshold Limit Values were devised to identify the level of risk for the most
sensitive individuals in the in the workplace.
a. true
b. false - CORRECT ANSWER - b. false
An example of an engineering control is:
a. full body coverage with gown, shoe covers, gloves and goggles
b. strictly enforced safety rules
c. all of the above
d. none of the above - CORRECT ANSWER - d. none of the above
Emergency response plans, training and occupational health programs are
examples of:
a. engineering controls
b. administrative controls
c. personal protective equipment
d. none of the above - CORRECT ANSWER - b. administrative controls
In the "hierarchy of controls", which type of control is considered the best?
a. engineering controls
, b. administrative controls
c. PPE
d. hiring controls - CORRECT ANSWER - a. engineering controls
A Task Hazard Analysis:
a. is required for each job by federal regulations
b. is a good approach to identify hazards
c. should be done by supervisors and managers rather than workers
d. is not a part of an occupational health and safety management system -
CORRECT ANSWER - b. is a good approach to identify hazards
The concept in legislation that indicates that "employers must do everything
reasonable to protect the health and safety of workers" is referred to as:
a. the rights of workers
b. refusal of unsafe work
c. due diligence
d. worker's compensation - CORRECT ANSWER - c. due diligence
In the Internal Responsibility System model, management is usually required to:
a. Correct hazards
b. Provide training
c. Investigate accidents
d. All of the above - CORRECT ANSWER - d. All of the above
SAFETY MANUAL
PRACTICE QUESTIONS
VERIFIED QUESTIONS AND
ANSWERS GRADED A+
,What are the major ways to deal with risk?
a. ignore them, make employees sign non-liability contracts
b. worker's compensation
c. report to government
d. tolerate, treat, terminate or transfer the risk - CORRECT ANSWER - d. tolerate,
treat, terminate or transfer the risk
Name the 5 categories of hazards: - CORRECT ANSWER –
1. chemical
2. biological
3. physical
4. ergonomic
5. psychological
Which of the following may be useful in helping to identify laboratory hazards?
a. safety data sheets
b. inspections
c. incident reports
d. all of the above - CORRECT ANSWER - d. all of the above
Personal monitoring can be used to measure noise exposure.
a. true
b. false - CORRECT ANSWER - a. true
,Standards for all chemicals that identify allowable levels of exposure are available.
a. true
b. false - CORRECT ANSWER - b. false
Threshold Limit Values were devised to identify the level of risk for the most
sensitive individuals in the in the workplace.
a. true
b. false - CORRECT ANSWER - b. false
An example of an engineering control is:
a. full body coverage with gown, shoe covers, gloves and goggles
b. strictly enforced safety rules
c. all of the above
d. none of the above - CORRECT ANSWER - d. none of the above
Emergency response plans, training and occupational health programs are
examples of:
a. engineering controls
b. administrative controls
c. personal protective equipment
d. none of the above - CORRECT ANSWER - b. administrative controls
In the "hierarchy of controls", which type of control is considered the best?
a. engineering controls
, b. administrative controls
c. PPE
d. hiring controls - CORRECT ANSWER - a. engineering controls
A Task Hazard Analysis:
a. is required for each job by federal regulations
b. is a good approach to identify hazards
c. should be done by supervisors and managers rather than workers
d. is not a part of an occupational health and safety management system -
CORRECT ANSWER - b. is a good approach to identify hazards
The concept in legislation that indicates that "employers must do everything
reasonable to protect the health and safety of workers" is referred to as:
a. the rights of workers
b. refusal of unsafe work
c. due diligence
d. worker's compensation - CORRECT ANSWER - c. due diligence
In the Internal Responsibility System model, management is usually required to:
a. Correct hazards
b. Provide training
c. Investigate accidents
d. All of the above - CORRECT ANSWER - d. All of the above
