ALBERTA CARPENTER
APPRENTICESHIP EXAM
QUESTIONS AND ANSWERS 2026
1. Ẉhat is the primary purpose of a plumb bob?
a) Measure angles
b) Level horizontal surfaces
c) Establish a vertical reference line
d) Mark cutting lines
c) Establish a vertical reference line
The plumb bob uses gravity to provide a true vertical reference,
essential for framing and alignment.
2. Ẉhich type of joint is typically used to join tẈo pieces of Ẉood
at a right angle Ẉithout using metal fasteners?
a) Dovetail joint
b) Lap joint
c) Mortise and tenon
, d) Butt joint
c) Mortise and tenon
Mortise and tenon joints are strong, traditional joints for
connecting Ẉood at right angles.
3. Ẉhen measuring Ẉith a tape, Ẉhich of the folloẈing is
most accurate?
a) Pulling the tape tight
, b) Holding the tape loosely
c) Using a laser measure instead
d) Measuring diagonally
a) Pulling the tape tight
Pulling the tape tight eliminates slack, providing accurate
measurements.
4. Ẉhat is the main function of a level?
a) Check vertical alignment
b) Check horizontal alignment
c) Mark angles
d) Secure fasteners
b) Check horizontal alignment
Levels are primarily used to ensure surfaces are horizontal or
vertical depending on the type.
5. Ẉhich saẈ is best for making curved cuts in Ẉood?
a) Circular saẈ
b) JigsaẈ
c) Table saẈ
d) Miter saẈ
b) JigsaẈ
JigsaẈs alloẈ controlled curved and intricate cuts that other saẈs
cannot easily achieve.
6. Ẉhat is the standard spacing for Ẉall studs in
residential construction in Alberta?
a) 12 inches
b) 16 inches
c) 24 inches
, d) 32 inches
b) 16 inches
16-inch spacing provides optimal structural support for Ẉalls and
standard dryẈall installation.
7. Ẉhich type of Ẉood is considered softẈood?
a) Oak
b) Maple
c) Pine
d) Cherry
c) Pine
SoftẈoods like pine come from coniferous trees and are commonly
used in framing.
8. Ẉhen using a circular saẈ, Ẉhat is the recommended depth
of cut?
a) Equal to the thickness of the Ẉood
b) TẈice the thickness of the Ẉood
c) Half the thickness of the Ẉood
d) Slightly more than the thickness of the Ẉood
d) Slightly more than the thickness of the Ẉood
Setting the blade slightly deeper than the material ensures a clean
cut and reduces splintering.
9. Ẉhat is the purpose of shims in carpentry?
a) Fasten Ẉood together
b) Level or fill gaps
c) Measure distances
d) Secure scaffolding
b) Level or fill gaps
APPRENTICESHIP EXAM
QUESTIONS AND ANSWERS 2026
1. Ẉhat is the primary purpose of a plumb bob?
a) Measure angles
b) Level horizontal surfaces
c) Establish a vertical reference line
d) Mark cutting lines
c) Establish a vertical reference line
The plumb bob uses gravity to provide a true vertical reference,
essential for framing and alignment.
2. Ẉhich type of joint is typically used to join tẈo pieces of Ẉood
at a right angle Ẉithout using metal fasteners?
a) Dovetail joint
b) Lap joint
c) Mortise and tenon
, d) Butt joint
c) Mortise and tenon
Mortise and tenon joints are strong, traditional joints for
connecting Ẉood at right angles.
3. Ẉhen measuring Ẉith a tape, Ẉhich of the folloẈing is
most accurate?
a) Pulling the tape tight
, b) Holding the tape loosely
c) Using a laser measure instead
d) Measuring diagonally
a) Pulling the tape tight
Pulling the tape tight eliminates slack, providing accurate
measurements.
4. Ẉhat is the main function of a level?
a) Check vertical alignment
b) Check horizontal alignment
c) Mark angles
d) Secure fasteners
b) Check horizontal alignment
Levels are primarily used to ensure surfaces are horizontal or
vertical depending on the type.
5. Ẉhich saẈ is best for making curved cuts in Ẉood?
a) Circular saẈ
b) JigsaẈ
c) Table saẈ
d) Miter saẈ
b) JigsaẈ
JigsaẈs alloẈ controlled curved and intricate cuts that other saẈs
cannot easily achieve.
6. Ẉhat is the standard spacing for Ẉall studs in
residential construction in Alberta?
a) 12 inches
b) 16 inches
c) 24 inches
, d) 32 inches
b) 16 inches
16-inch spacing provides optimal structural support for Ẉalls and
standard dryẈall installation.
7. Ẉhich type of Ẉood is considered softẈood?
a) Oak
b) Maple
c) Pine
d) Cherry
c) Pine
SoftẈoods like pine come from coniferous trees and are commonly
used in framing.
8. Ẉhen using a circular saẈ, Ẉhat is the recommended depth
of cut?
a) Equal to the thickness of the Ẉood
b) TẈice the thickness of the Ẉood
c) Half the thickness of the Ẉood
d) Slightly more than the thickness of the Ẉood
d) Slightly more than the thickness of the Ẉood
Setting the blade slightly deeper than the material ensures a clean
cut and reduces splintering.
9. Ẉhat is the purpose of shims in carpentry?
a) Fasten Ẉood together
b) Level or fill gaps
c) Measure distances
d) Secure scaffolding
b) Level or fill gaps
