SACA C-215 Robotic Systems EXAM STUDY
GUIDE 2026/2027 ACCURATE QUESTIONS WITH
CORRECT DETAILED SOLUTIONS || 100%
GUARANTEED PASS NEWEST VERSION
Save
Terms in this set (50)
Which type of robot griper can D. Electro Servo
adjust Its finger position based on
feedback?
A. Pnumatic 2-point
B. Pnumatic 3-point
C. Hydraulic
D. Electro Servo
When a robot is in automatic cycle, D. Selecting programs
what function is active on the teach
pendant?
A. Teaching points
B. Downloading programs
C. Editing programs
D. Selecting programs
,How would you verify that the axis C. Compare axis position when robot axes are
position information shown on a aligned with calibration marks
teach pendent is accurate while in
joint jog mode?
A. Perform axis calibration
procedure with teach pendant
B. Set up a work cell zero reference
point
C. Compare axis position when
robot axes are aligned with
calibration marks
D. Master the robot
what type of robot is shown B. SCARA
(different image)?
A. Gantry
B. SCARA
C. Articulated
D. Non-servo
, Which of these can affect the range B. Machine guard/Safety fence
of a robot's work envelope?
A. Axis motor size
B. Machine guard/Safety fence
C. Program
D. End of arm tooling
What device is used to manually B. Teach pendant
adjust robot position when
programming robot points?
A. Operator panel
B. Teach pendant
C. Controller
D. Manipulator
Which jog frame mode would be A. User
easiest to use to jog the robot tool
tip along the line shown on the
work piece surface with the tool
1mm away from the surface?
(Image not shown)
A. User
B. World
C. Automatic
D. Joint
How does the operator recover a B. Fix the error. Then press reset or restart the
robot from most errors? robot
A. Run an error diagnostic
B. Fix the error. Then press reset or
restart the robot
C. Press reset and restart robot
D. Clear the alarm log
GUIDE 2026/2027 ACCURATE QUESTIONS WITH
CORRECT DETAILED SOLUTIONS || 100%
GUARANTEED PASS NEWEST VERSION
Save
Terms in this set (50)
Which type of robot griper can D. Electro Servo
adjust Its finger position based on
feedback?
A. Pnumatic 2-point
B. Pnumatic 3-point
C. Hydraulic
D. Electro Servo
When a robot is in automatic cycle, D. Selecting programs
what function is active on the teach
pendant?
A. Teaching points
B. Downloading programs
C. Editing programs
D. Selecting programs
,How would you verify that the axis C. Compare axis position when robot axes are
position information shown on a aligned with calibration marks
teach pendent is accurate while in
joint jog mode?
A. Perform axis calibration
procedure with teach pendant
B. Set up a work cell zero reference
point
C. Compare axis position when
robot axes are aligned with
calibration marks
D. Master the robot
what type of robot is shown B. SCARA
(different image)?
A. Gantry
B. SCARA
C. Articulated
D. Non-servo
, Which of these can affect the range B. Machine guard/Safety fence
of a robot's work envelope?
A. Axis motor size
B. Machine guard/Safety fence
C. Program
D. End of arm tooling
What device is used to manually B. Teach pendant
adjust robot position when
programming robot points?
A. Operator panel
B. Teach pendant
C. Controller
D. Manipulator
Which jog frame mode would be A. User
easiest to use to jog the robot tool
tip along the line shown on the
work piece surface with the tool
1mm away from the surface?
(Image not shown)
A. User
B. World
C. Automatic
D. Joint
How does the operator recover a B. Fix the error. Then press reset or restart the
robot from most errors? robot
A. Run an error diagnostic
B. Fix the error. Then press reset or
restart the robot
C. Press reset and restart robot
D. Clear the alarm log
