PLUMBERS AND PIPE FITTERS EXAM WITH ALL CORRECT ANSWERS
What pipe hanger is shown in the following figure?
A. Riser Clamp
B. Adjustable Clevis
C. Trapeze
D. Heavy strap
B. Adjustable Clevis
The industrialized piece of equipment is a ?
A. Boom Truck
B. Cherry Picker
C. Fork Truck
D. Compact Trencher
B. Cherry Picker
The flange depicted by the following figure is a ?
A. Slip On
B. Socket Weld
C. Blind
D. Weld Neck
D. Weld Neck
,The industrialized piece of equipment is a ?
A. Boom Truck
B. Cherry Picker
C. Fork Truck
D. Compact Trencher
D. Compact Trencher
When using shoring to support walls in an evacuation, which of the following would NOT be
used?
A. Upright
B. Wales
C. Cross braces
D. Soil anchor
B. Wales
What is used to reduce or increase pipe sizes in threaded pipelines?
A. Unions
B. Couplings
C. Bushings
D. Nipples
C. Bushings
Chain come-alongs are PRIMARILY designed for:
,A. Lifting in close quarters.
B. Vertical lifting.
C. Lifting in any location.
D. Horizontal lifting.
D. Horizontal lifting.
A piping and instrumentation drawing would show which of the following?
A. Direction of flow
B. Bill of material
C. Elevation
D. Plan view
D. Plan view
Thrust blocks shall be placed against:
A. the top of the pipe.
B. the side of the pipe.
C. undisturbed soil.
D. compacted soil.
D. compacted soil.
What type of working application should be used on a slip-on flange?
A. Fillet-weld
B. Stitch-weld
, C. Butt-weld
D. Socket-weld
A. Fillet-weld
While installing a 3-inch diameter pipe run under a beam, beam clamps and clevis hangers are
used. The REQUIRED centerline elevation for the pipe is 22 feet at both beams. What is the BOP
elevation for the 3-inch pipe?
A. 21 feet 9 ¾ inches
B. 21 feet 10 ¼ inches
C. 22 feet
D. 22 feet 1 ¾ inches
B. 21 feet 10 ¼ inches
A line drawn along the surface of the pipe at division points that serves as a guide for cutting
miters and making contours is known as:
A. centerline.
B. an ordinate line.
C. a piece mark.
D. a chalk line.
B. an ordinate line.
Find the lowest common denominator for 1/8 and 1/2.
A. 3
B. 5
What pipe hanger is shown in the following figure?
A. Riser Clamp
B. Adjustable Clevis
C. Trapeze
D. Heavy strap
B. Adjustable Clevis
The industrialized piece of equipment is a ?
A. Boom Truck
B. Cherry Picker
C. Fork Truck
D. Compact Trencher
B. Cherry Picker
The flange depicted by the following figure is a ?
A. Slip On
B. Socket Weld
C. Blind
D. Weld Neck
D. Weld Neck
,The industrialized piece of equipment is a ?
A. Boom Truck
B. Cherry Picker
C. Fork Truck
D. Compact Trencher
D. Compact Trencher
When using shoring to support walls in an evacuation, which of the following would NOT be
used?
A. Upright
B. Wales
C. Cross braces
D. Soil anchor
B. Wales
What is used to reduce or increase pipe sizes in threaded pipelines?
A. Unions
B. Couplings
C. Bushings
D. Nipples
C. Bushings
Chain come-alongs are PRIMARILY designed for:
,A. Lifting in close quarters.
B. Vertical lifting.
C. Lifting in any location.
D. Horizontal lifting.
D. Horizontal lifting.
A piping and instrumentation drawing would show which of the following?
A. Direction of flow
B. Bill of material
C. Elevation
D. Plan view
D. Plan view
Thrust blocks shall be placed against:
A. the top of the pipe.
B. the side of the pipe.
C. undisturbed soil.
D. compacted soil.
D. compacted soil.
What type of working application should be used on a slip-on flange?
A. Fillet-weld
B. Stitch-weld
, C. Butt-weld
D. Socket-weld
A. Fillet-weld
While installing a 3-inch diameter pipe run under a beam, beam clamps and clevis hangers are
used. The REQUIRED centerline elevation for the pipe is 22 feet at both beams. What is the BOP
elevation for the 3-inch pipe?
A. 21 feet 9 ¾ inches
B. 21 feet 10 ¼ inches
C. 22 feet
D. 22 feet 1 ¾ inches
B. 21 feet 10 ¼ inches
A line drawn along the surface of the pipe at division points that serves as a guide for cutting
miters and making contours is known as:
A. centerline.
B. an ordinate line.
C. a piece mark.
D. a chalk line.
B. an ordinate line.
Find the lowest common denominator for 1/8 and 1/2.
A. 3
B. 5
