SACA EXAM QUESTIONS AND
ANSWERS | 2026 UPDATE | 100%
CORRECT.
What is the pressure shown on this gauge?* - ANS 500 kPa
What type of wrench is shown?* - ANS Ratchet
What amount of power is used in this circuit?* - ANS 96W
What type of geometric tolerance is shown in the feature control frame on this drawing? -
ANS Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? -
ANS Machine operation procedures
What action must be taken to correctly position a dial caliper? - ANS Sweep and rock to the
jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* -
ANS Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
@COPYRIGHT ALL RIGHTS RESERVED PAGE 1 OF 7
, 0/4 - ANS Moving a product from one station to another
What is the tolerance of the width of this part?* - ANS +/-0.1
What do SDS sheets do?* - ANS Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper
torque? - ANS Stop turning the wrench
What type of hole is identified by the arrow labeled A?* - ANS Blind
What component does the schematic represent?* - ANS Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - ANS General notes
What machine can be programmed to perform tasks in many different operations? -
ANS Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - ANS metal
Which of these is NOT a primary goal of a lean manufacturing system? - ANS Greater
production volume
In the bolt designation shown, what is the pitch? - ANS 2.5
What air pressure should be used when compressed air is used to clean or blow parts? -
ANS Below 30 psi
@COPYRIGHT ALL RIGHTS RESERVED PAGE 2 OF 7
ANSWERS | 2026 UPDATE | 100%
CORRECT.
What is the pressure shown on this gauge?* - ANS 500 kPa
What type of wrench is shown?* - ANS Ratchet
What amount of power is used in this circuit?* - ANS 96W
What type of geometric tolerance is shown in the feature control frame on this drawing? -
ANS Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except? -
ANS Machine operation procedures
What action must be taken to correctly position a dial caliper? - ANS Sweep and rock to the
jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* -
ANS Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
@COPYRIGHT ALL RIGHTS RESERVED PAGE 1 OF 7
, 0/4 - ANS Moving a product from one station to another
What is the tolerance of the width of this part?* - ANS +/-0.1
What do SDS sheets do?* - ANS Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the proper
torque? - ANS Stop turning the wrench
What type of hole is identified by the arrow labeled A?* - ANS Blind
What component does the schematic represent?* - ANS Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - ANS General notes
What machine can be programmed to perform tasks in many different operations? -
ANS Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - ANS metal
Which of these is NOT a primary goal of a lean manufacturing system? - ANS Greater
production volume
In the bolt designation shown, what is the pitch? - ANS 2.5
What air pressure should be used when compressed air is used to clean or blow parts? -
ANS Below 30 psi
@COPYRIGHT ALL RIGHTS RESERVED PAGE 2 OF 7
