STATE BRAKE CERTIFICATION NEWEST 2026/2027
ACTUAL EXAM COMPLETE QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |ALREADY GRADED A+| INSTANT PDF
DOWNLOAD
Federal Motor Vehicle Safety Standards require that automative parking
brakes be capable of holding a vehicle stationary on a ________ degree
grade
A. 70
B. 10
C. 50
D. 30 SELECTED ANSWER
In a drum brake system, the rotational action of the brake shoes activates
the self-adjuster linkage when the brakes are applied and the vehicle is
_________
A. Moving forward
B. In reverse SELECTED ANSWER
C. Braking in either direction
D. Suddenly stopped
Correct procedures must be followed when working with asbestos
because it:
A. Is highly flammable
B. Produces poisonous gas
C. Is explosive
D. Is a cancer-causing substance SELECTED ANSWER
Which brake fluid is silicone based
,A. ALL are silicone based
B. DOT 3
C. DOT 5 SELECTED ANSWER
D. DOT 4
Pressure differential valves are spring-loaded plunger valves that are used
to turn on dashboard warning lights if hydraulic pressure is lost in
_______
A. Either front or rear brake systems SELECTED ANSWER
B. Wheel cylinders or calipers only
C. Rear brake systems only
D. Front brake systems only
For a brake rotor to be parallel, no two micrometer measurements should
vary by more than _______
A. .0001 inches
B. .001 inches SELECTED ANSWER
C. .010 inches
D. .005 inches
On drum brake systems, the wheel cylinders are always fastened firmly to
the ________
A. Anchor
B. Hub
C. Brake backing plate SELECTED ANSWER
D. Wheel well
Annual inspections of brake linings are recommended for all vehicles with
more than ________
A. 40,000 miles
B. 100,000 miles
C. 60,000 miles
D. 20,000 miles SELECTED ANSWER
, A check valve for a vacuum booster holds vacuum pressure and assures
power assist capability when ___________________
A. There is a low engine vacuum SELECTED ANSWER
B. There is a loss of power assist
C. There is a loss of brake fluid
D. The master cylinder fails
Which of the following statements is true
A. The larger the tire's diameter is, the less braking power is required
B. The larger the tire's diameter is, the smaller its footprint is
C. The larger the tire's footprint is, the more stopping power can be applied at
the tire's contact point with the road SELECTED ANSWER
D. The smaller the tire's diameter is, the larger its footprint is
A vehicle can be safely supported with ________
A. A bumper jack
B. A bumper jack and blocks
C. Blocks
D. None of the choices are correct SELECTED ANSWER
Gauge sets used to test proportioning valves must be able to withstand
pressures up to _____-
A. 1,200 psi
B. 1,750 psi
C. 1,500 psi SELECTED ANSWER
D. 2,500 psi
The most basic brake modulator control valve is __________
A. a bleeder valve
B. a dump/decay valve
ACTUAL EXAM COMPLETE QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |ALREADY GRADED A+| INSTANT PDF
DOWNLOAD
Federal Motor Vehicle Safety Standards require that automative parking
brakes be capable of holding a vehicle stationary on a ________ degree
grade
A. 70
B. 10
C. 50
D. 30 SELECTED ANSWER
In a drum brake system, the rotational action of the brake shoes activates
the self-adjuster linkage when the brakes are applied and the vehicle is
_________
A. Moving forward
B. In reverse SELECTED ANSWER
C. Braking in either direction
D. Suddenly stopped
Correct procedures must be followed when working with asbestos
because it:
A. Is highly flammable
B. Produces poisonous gas
C. Is explosive
D. Is a cancer-causing substance SELECTED ANSWER
Which brake fluid is silicone based
,A. ALL are silicone based
B. DOT 3
C. DOT 5 SELECTED ANSWER
D. DOT 4
Pressure differential valves are spring-loaded plunger valves that are used
to turn on dashboard warning lights if hydraulic pressure is lost in
_______
A. Either front or rear brake systems SELECTED ANSWER
B. Wheel cylinders or calipers only
C. Rear brake systems only
D. Front brake systems only
For a brake rotor to be parallel, no two micrometer measurements should
vary by more than _______
A. .0001 inches
B. .001 inches SELECTED ANSWER
C. .010 inches
D. .005 inches
On drum brake systems, the wheel cylinders are always fastened firmly to
the ________
A. Anchor
B. Hub
C. Brake backing plate SELECTED ANSWER
D. Wheel well
Annual inspections of brake linings are recommended for all vehicles with
more than ________
A. 40,000 miles
B. 100,000 miles
C. 60,000 miles
D. 20,000 miles SELECTED ANSWER
, A check valve for a vacuum booster holds vacuum pressure and assures
power assist capability when ___________________
A. There is a low engine vacuum SELECTED ANSWER
B. There is a loss of power assist
C. There is a loss of brake fluid
D. The master cylinder fails
Which of the following statements is true
A. The larger the tire's diameter is, the less braking power is required
B. The larger the tire's diameter is, the smaller its footprint is
C. The larger the tire's footprint is, the more stopping power can be applied at
the tire's contact point with the road SELECTED ANSWER
D. The smaller the tire's diameter is, the larger its footprint is
A vehicle can be safely supported with ________
A. A bumper jack
B. A bumper jack and blocks
C. Blocks
D. None of the choices are correct SELECTED ANSWER
Gauge sets used to test proportioning valves must be able to withstand
pressures up to _____-
A. 1,200 psi
B. 1,750 psi
C. 1,500 psi SELECTED ANSWER
D. 2,500 psi
The most basic brake modulator control valve is __________
A. a bleeder valve
B. a dump/decay valve
