MSSC - Quality Certification
Study online at https://quizlet.com/_1b1qaq
1. Which is NOT one of the steps used in the glass box method?: rotate object in glass
box
2. The three standard views of an object are ______.: top, front, right side
3. What is the order of precedence of lines in a drawing?: object, hidden, center
4. What type of feature is parallel to the surface being dimensioned?: dimension line
5. A ______ dimension is described in inches per foot.: shaft taper
6. To establish on a drawing that 1/4 inch equals 1 inch, the designer would write
______.: 1/4 = 1
7. Section lines on a blueprint include _______.: a surface that has been cut
8. In a threaded fastener assembly what is designed to protect the threads?: shank
9. The minor diameter of a screw thread is measured at the ______.: root of screw thread
10. The minor diameter of a threaded fastener is ______.: the major diameter minus the
thread height
11. How do you determine the grade of a bolt?: number of lines on the head +2 indicates the
grade
12. A screw with National fine thread is represented on a drawing with what
designation?: NF
13. Metals treated by ______ processes become soft.: annealing
14. A running fit is also called a(n) ______.: sliding fit
15. The term ______ refers to a physical portion of a part.: feature
16. A(n) _______ is a theoretically perfect line, point or pane that is located by a
similar feature or part.: datum
17. GD&T _________________.: allows certain tolerances on part features to be increased
18. A feature control frame is not used to describe ______.: measurements
19. A common decimal inch rule graduation is in _______.: 50ths
20. A scale typically found on a machinist rule is _______.: 1/16
21. Resolution is sometimes called ______.: discrimination
22. A common fractional inch rule graduation is in _______.: 32nds
23. One inch is equal to _______.: 25.4mm
24. A typical dial caliper can be used to measure dimensions to the nearest
________ inches.: 0.001
25. Calibration means to ______.: adjust a device to a standard
1/6
, MSSC - Quality Certification
Study online at https://quizlet.com/_1b1qaq
26. The typical accuracy of a dial caliper is about ______ inches.: 0.003
27. The accuracy of a digital caliper reading is about ______ inches.: 0.003
28. A micrometer increments how far for each complete rotation of its thimble?-
: 0.025
29. Company standards determine how often ______ is performed.: calibration of
surface finish gaues
30. The dial indicator makes measurements using the ______ method.: indirect
comparison
31. The best method for checking the height of two or more parts is to use a dial
indicator and stand, gauge block and a ______.: surface plate
32. A _______ is a measurement tool that measures part dimensions by indicating
the amount of distance its probe moves when placed against the part.: dial indicator
33. _______ measures the difference between an object's dimension and an ob-
ject of known length.: indirect comparison
34. The process of zeroing the probe using a part that has been found to be a
precise length is known as ______.: mastering
35. A _______ avoids the errors of hand-held instruments by locating the parts in
the same place each time a measurement is made.: fixture
36. A key concept in continuous improvement is to search for ways to eliminate
waste in actions, time, and ______.: material
37. An important statistic is calculated by dividing the number of parts produced
by the number of hours worked. his statistic is called ______.: labor productivity
38. Parts labeled ______ should be inspected to determine if they should be
reworked or scrapped.: hold
39. An engineering change notice (ECN) is used to notify of changes _______.: on
a product drawing
40. Parts that are labeled as ok to ship must ______.: meet compliance
41. Machine time, quality requirements, and task time are ________.: required docu-
ments for a process
42. Machine time, task time, and quality requirements are information needed
to______.: document each process
2/6
Study online at https://quizlet.com/_1b1qaq
1. Which is NOT one of the steps used in the glass box method?: rotate object in glass
box
2. The three standard views of an object are ______.: top, front, right side
3. What is the order of precedence of lines in a drawing?: object, hidden, center
4. What type of feature is parallel to the surface being dimensioned?: dimension line
5. A ______ dimension is described in inches per foot.: shaft taper
6. To establish on a drawing that 1/4 inch equals 1 inch, the designer would write
______.: 1/4 = 1
7. Section lines on a blueprint include _______.: a surface that has been cut
8. In a threaded fastener assembly what is designed to protect the threads?: shank
9. The minor diameter of a screw thread is measured at the ______.: root of screw thread
10. The minor diameter of a threaded fastener is ______.: the major diameter minus the
thread height
11. How do you determine the grade of a bolt?: number of lines on the head +2 indicates the
grade
12. A screw with National fine thread is represented on a drawing with what
designation?: NF
13. Metals treated by ______ processes become soft.: annealing
14. A running fit is also called a(n) ______.: sliding fit
15. The term ______ refers to a physical portion of a part.: feature
16. A(n) _______ is a theoretically perfect line, point or pane that is located by a
similar feature or part.: datum
17. GD&T _________________.: allows certain tolerances on part features to be increased
18. A feature control frame is not used to describe ______.: measurements
19. A common decimal inch rule graduation is in _______.: 50ths
20. A scale typically found on a machinist rule is _______.: 1/16
21. Resolution is sometimes called ______.: discrimination
22. A common fractional inch rule graduation is in _______.: 32nds
23. One inch is equal to _______.: 25.4mm
24. A typical dial caliper can be used to measure dimensions to the nearest
________ inches.: 0.001
25. Calibration means to ______.: adjust a device to a standard
1/6
, MSSC - Quality Certification
Study online at https://quizlet.com/_1b1qaq
26. The typical accuracy of a dial caliper is about ______ inches.: 0.003
27. The accuracy of a digital caliper reading is about ______ inches.: 0.003
28. A micrometer increments how far for each complete rotation of its thimble?-
: 0.025
29. Company standards determine how often ______ is performed.: calibration of
surface finish gaues
30. The dial indicator makes measurements using the ______ method.: indirect
comparison
31. The best method for checking the height of two or more parts is to use a dial
indicator and stand, gauge block and a ______.: surface plate
32. A _______ is a measurement tool that measures part dimensions by indicating
the amount of distance its probe moves when placed against the part.: dial indicator
33. _______ measures the difference between an object's dimension and an ob-
ject of known length.: indirect comparison
34. The process of zeroing the probe using a part that has been found to be a
precise length is known as ______.: mastering
35. A _______ avoids the errors of hand-held instruments by locating the parts in
the same place each time a measurement is made.: fixture
36. A key concept in continuous improvement is to search for ways to eliminate
waste in actions, time, and ______.: material
37. An important statistic is calculated by dividing the number of parts produced
by the number of hours worked. his statistic is called ______.: labor productivity
38. Parts labeled ______ should be inspected to determine if they should be
reworked or scrapped.: hold
39. An engineering change notice (ECN) is used to notify of changes _______.: on
a product drawing
40. Parts that are labeled as ok to ship must ______.: meet compliance
41. Machine time, quality requirements, and task time are ________.: required docu-
ments for a process
42. Machine time, task time, and quality requirements are information needed
to______.: document each process
2/6
