DETAILED
ANSWERS|LATEST!!!!2025/2026|GUARANTEED
Who is responsible for identifying the assembly class? - ANSWER User
What is a defect? - ANSWER A condition that may affect the form, fit, or function of
the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be classified as
defects and dispositioned for: - ANSWER [D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
ANSWER [D1D2D3]
A documented process control system shall be implemented for: - ANSWER [N1N2D3]
The contract shall take precedence over this standard for: - ANSWER [D1D2D3]
What is wire overlap? - ANSWER When a wire is wrapped more than 360 and crosses
over itself
What is wire over wrap? - ANSWER When a wire is wrapped more than 360 and
remains in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for: -
ANSWER [N1D2D3]
1
, Inspection of soldering and cleanliness shall be performed prior to conformal coasting,
staking, or encapsulation for: - ANSWER [N1D2D3]
Illumination at the surface of work stations should be at least what? - ANSWER 1000
lux
What is the tolerance for magnification aids? - ANSWER +- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
ANSWER [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
ANSWER [N1D2D3]
Manufacturer shall establish an ESD control program for: - ANSWER [D1D2D3]
What is J-STD-002? - ANSWER Solder-ability tests for Component leads, terminations,
lugs, wires, and terminals
What is J-STD-003? - ANSWER Solder ability tests for printed boards
What is J-STD-004? - ANSWER Requirements for Soldering Fluxes
What is J-STD-005? - ANSWER Requirements for Soldering Paste
What is J-STD-006? - ANSWER Requirements for electronic grade solder alloys, fluxed
and non-fluxed solid solders
2
ANSWERS|LATEST!!!!2025/2026|GUARANTEED
Who is responsible for identifying the assembly class? - ANSWER User
What is a defect? - ANSWER A condition that may affect the form, fit, or function of
the item in the end use environment
Hardware found to not conform to the requirements of the standard shall be classified as
defects and dispositioned for: - ANSWER [D1D2D3]
There shall be no broken strands for wires used at a potential of 6kV or greater: -
ANSWER [D1D2D3]
A documented process control system shall be implemented for: - ANSWER [N1N2D3]
The contract shall take precedence over this standard for: - ANSWER [D1D2D3]
What is wire overlap? - ANSWER When a wire is wrapped more than 360 and crosses
over itself
What is wire over wrap? - ANSWER When a wire is wrapped more than 360 and
remains in contact with the terminal
Manufacturers shall perform 100% inspection unless sampling inspection is defined for: -
ANSWER [N1D2D3]
1
, Inspection of soldering and cleanliness shall be performed prior to conformal coasting,
staking, or encapsulation for: - ANSWER [N1D2D3]
Illumination at the surface of work stations should be at least what? - ANSWER 1000
lux
What is the tolerance for magnification aids? - ANSWER +- 15%
Eating, drinking, smoking, e-cigs use shall be prohibited at the work station for: -
ANSWER [D1D2D3]
Manufacturer shall verify ESD is adequate when humidity falls below 30% for: -
ANSWER [N1D2D3]
Manufacturer shall establish an ESD control program for: - ANSWER [D1D2D3]
What is J-STD-002? - ANSWER Solder-ability tests for Component leads, terminations,
lugs, wires, and terminals
What is J-STD-003? - ANSWER Solder ability tests for printed boards
What is J-STD-004? - ANSWER Requirements for Soldering Fluxes
What is J-STD-005? - ANSWER Requirements for Soldering Paste
What is J-STD-006? - ANSWER Requirements for electronic grade solder alloys, fluxed
and non-fluxed solid solders
2
