AUTO ENGINE REPAIR (SOS MICHIGAN TEST PREP VALVE
TRAIN) QUESTIONS AND CORRECT DETAILED ANSWERS
<VERIFIED ANSWERS> |LATEST UPLOAD |ALREADY
GRADED A+
What is enclosed in the vehicle vin? - ANS -Engine type, body style, and transmission type.
A compression test shows that one cylinder shows to much leakage. During the air test could be heard
coming from the tailpipe what could be the cause?
A) bad piston rings
B) bad head gasket
C) bad exhaust gasket
D) exhaust valve not seating - ANS -D.) exhaust valve not seating
Technician A says that main bearing oil clearances can be checked with pasty gages.
Technician B says that main bearing oil clearances can be checked with a feeler gauge. Who is Correct? -
ANS -Tech A
An engine is burning to much oil. Technician A says it’s the valve guides. Technician B says its tapered
cylinder walls. Who is correct? - ANS -Both
A compression test is being done on an in- line four-cylinder engine. Cylinder two and three have
readings of 10 psi cylinder one has a reading of 140 psi and cylinder four has 145psi.
Technician A says it’s a blown head gasket
Technician B says its bad valve timing. - ANS -Tech A
What is the most likely cause of low fuel pressure in a fuel injection engine?
A) clogged fuel filter
, B) clogged injector
C) restricted fuel line
D) stuck closed pressure regulator - ANS -A) clogged fuel filter
The pressure and volume of a mechanical fuel pump are both below spec.
Technician A says that an air leak in the fuel line between the tank and the pump could be the cause.
Technician B says that a plugged fuel tank pick-up filter is the cause. - ANS -Both
The most likely cause of a bent push rod? - ANS -Excessive valve guide clearance
Technician A says that it is important to drive the customer’s vehicle to verify the complaint as part of
your diagnosis procedure.
Technician B says it’s a good idea to check for related TSB's - ANS -Both
Technician A says the main bearing clearances can be checked with pasty gauges.
Technician B says that you can check main bearing clearances with a feeler gauge. Who is correct? - ANS
-Tech A
The oil filter on a customer's car is bulged out.
Technician A says this could be caused by an improper filter installation.
Technician B says this can only be caused by a pressure regulator that is stuck. Who is correct? - ANS -
Tech B
Technician A says that a turbocharger boost is controlled by a waste gate.
Technician B says the waste gate is controlled by the engine vacuum.
Who is correct? - ANS -Both
NATEF certifies automotive:
A) dealerships
B) independent garages
TRAIN) QUESTIONS AND CORRECT DETAILED ANSWERS
<VERIFIED ANSWERS> |LATEST UPLOAD |ALREADY
GRADED A+
What is enclosed in the vehicle vin? - ANS -Engine type, body style, and transmission type.
A compression test shows that one cylinder shows to much leakage. During the air test could be heard
coming from the tailpipe what could be the cause?
A) bad piston rings
B) bad head gasket
C) bad exhaust gasket
D) exhaust valve not seating - ANS -D.) exhaust valve not seating
Technician A says that main bearing oil clearances can be checked with pasty gages.
Technician B says that main bearing oil clearances can be checked with a feeler gauge. Who is Correct? -
ANS -Tech A
An engine is burning to much oil. Technician A says it’s the valve guides. Technician B says its tapered
cylinder walls. Who is correct? - ANS -Both
A compression test is being done on an in- line four-cylinder engine. Cylinder two and three have
readings of 10 psi cylinder one has a reading of 140 psi and cylinder four has 145psi.
Technician A says it’s a blown head gasket
Technician B says its bad valve timing. - ANS -Tech A
What is the most likely cause of low fuel pressure in a fuel injection engine?
A) clogged fuel filter
, B) clogged injector
C) restricted fuel line
D) stuck closed pressure regulator - ANS -A) clogged fuel filter
The pressure and volume of a mechanical fuel pump are both below spec.
Technician A says that an air leak in the fuel line between the tank and the pump could be the cause.
Technician B says that a plugged fuel tank pick-up filter is the cause. - ANS -Both
The most likely cause of a bent push rod? - ANS -Excessive valve guide clearance
Technician A says that it is important to drive the customer’s vehicle to verify the complaint as part of
your diagnosis procedure.
Technician B says it’s a good idea to check for related TSB's - ANS -Both
Technician A says the main bearing clearances can be checked with pasty gauges.
Technician B says that you can check main bearing clearances with a feeler gauge. Who is correct? - ANS
-Tech A
The oil filter on a customer's car is bulged out.
Technician A says this could be caused by an improper filter installation.
Technician B says this can only be caused by a pressure regulator that is stuck. Who is correct? - ANS -
Tech B
Technician A says that a turbocharger boost is controlled by a waste gate.
Technician B says the waste gate is controlled by the engine vacuum.
Who is correct? - ANS -Both
NATEF certifies automotive:
A) dealerships
B) independent garages
