Suspensi Guías de estudio, Notas de estudios & Resúmenes

SOS MECHANIC CERTIFICATION- SUSPENSION & STEERING

Suspension and Steering Practice Test with Verified Solutions A vehicle has excessive body sway while cornering. Which of these is most likely to cause this condition. A. A binding ball joint. B. A warn idler arm. C. Warn control arm bushings. D. Warn stabilizer bar bushings D. Warn stabilizer bar bushings A vehicle with variable assist steering feels loose only at highway speeds. Technician A says this is likely caused by the vehicle speed sensor. Technician B says this could be ...

SOLVED - Elaborated ASE A4 ASE SUSPENSION & STEERING Exam 1 for 2023 Ace in your ExamsProf.Exams ASE A4 ASE SUSPENSION & STEERING Exam 1 for 2023 Ace in your Exams in 1 attempt! 1. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A a...

Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specification then back off a certain number of degrees. A customer says that the steering whee...

Which of the following is the proper way to adjust the rack yoke bearing? A. Tighten to 75 ft lbs. B. Tighten to 5 inch lbs. C. Tighten and then back off the original equipment manufacturer's (OEM) specifications. D. Tighten to 0.002" end-play. - Answer-Tighten and then back off the originial equipment manufacturer's (OEM) specifications. Many OEMs will recommend that the technician tighten to a specification then back off a certain number of degrees. A customer says that the steering ...

A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Technician A says that too much runout of the front wheels could be the cause. Technician B says that static out-of-balance of the front wheels could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A of B - Answer-The correct answer is C, both technicians are right. Too much runout or static out-of-balance in the front wheels will cause a vibr...

Which of the following is true about control arm bushings? A: They are located between the frame and the control arm. B: Worn control arm bushings result wheel shimmy. C: They are tightened on while unloaded and the vehicle is raised in the air D: Both A or B - Answer-D: Both A or B Technician A says that leaf spring shackle swivels and allows the spring to flatten as the vehicle travels over bumps in the road. Technician B says that a single crack in the longest blade of a multi-leaf lea...

1500 psi - Answer-High pressure hoses have to be used on the high pressure side of the power steering system because pressures can reach as high as __________. A) 200 psi B) 750 psi C) 2500 psi D) 1500 psi False - Answer-All power steering pumps have integral reservoirs. True or False? all of the above are correct - Answer-Which of the following represent typical power steering pressures? A) over 750 psi when slowly maneuvering a parking lot B) about 450 psi when cornering C) less t...

A vehicle wanders when driven on normal road surfaces. The steering wheel exhibits more play than usual. Which of these should the technician do first? A. Measure power steering pump output pressure. B. Flush the power steering fluid. C. Check for worn steering linkage. D. Measure front rotor lateral runout. - Answer-C. Check for worn steering linkage During a pre-alignment inspection of a high mileage vehicle, a technician sees oil dripping from one of the vehicle's front shock absorber...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE RATED A+ YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS WOULD BE FOUND AT: A. POINT...