Alberta welding first year final AIT exam 2025/2026
every three years
A Material Safety Data Sheet must be
reviewed whenever new information
becomes available or at least how often?
1800
What is the total number of hours of work
experience, including technical training,
required per year in the Welder
Apprenticeship Program?
arc voltage.
Voltage-sensing wire feeders set their
speed according to:
10 mm to 19 mm (3/8" to 3/4")
How much electrode stickout is
recommended when using gas shielded
FCAW with 1.2 mm (0.045") wire?
transfer current to the electrode.
One of the main functions of the contact
tube is to:
False
Flame propagation means the speed at
which the fuel gas will travel
For free standing scaffolds, the scaffold must not be taller than three (3) times its
What height limitation is in place when
smallest dimension in height
using freestanding scaffolding?
datum line
The best reference point for dimensioning
on pressure vessels is the:
UT
Which of the following is an abbreviation of
a Non destructive test ?
5
In common fabricating practice, there are
how many basic joint types?
3/8" -1" (9.5 -25.4mm)
Single "V" butt joints are used on material
thicknesses of:
sling load.
A small change in sling angle can
drastically affect the:
DC synergic, microprocessor-controlled.
The power sources used for pulsed spray
transfer are:
3/8" -1" (9.5 -25.4mm)
Single "V" butt joints are used on material
thicknesses of:
If you must apply force to a suspended
load, always pull the load towards you.
Live side of the wire
When installing clips, the saddle side of the
clip must be placed on the:
1/4
When balancing a No. 2 welding tip and
the acetylene torch needle valve is fully
open, the acetylene regulator should be
adjusted so that the flame blows away from
the tip _______ inch. (Oxygen needle
valve is closed)
stainless
Which ferrous-based metals cannot be cut
satisfactorily with an oxy-fuel cutting torch?
240
What is the total number of hours in the
first period Welder Training Profile?
about 3 mm (1/8") above the surface.
When starting a cut on plate, the preheat
cones should be held:
every three years
A Material Safety Data Sheet must be
reviewed whenever new information
becomes available or at least how often?
1800
What is the total number of hours of work
experience, including technical training,
required per year in the Welder
Apprenticeship Program?
arc voltage.
Voltage-sensing wire feeders set their
speed according to:
10 mm to 19 mm (3/8" to 3/4")
How much electrode stickout is
recommended when using gas shielded
FCAW with 1.2 mm (0.045") wire?
transfer current to the electrode.
One of the main functions of the contact
tube is to:
False
Flame propagation means the speed at
which the fuel gas will travel
For free standing scaffolds, the scaffold must not be taller than three (3) times its
What height limitation is in place when
smallest dimension in height
using freestanding scaffolding?
datum line
The best reference point for dimensioning
on pressure vessels is the:
UT
Which of the following is an abbreviation of
a Non destructive test ?
5
In common fabricating practice, there are
how many basic joint types?
3/8" -1" (9.5 -25.4mm)
Single "V" butt joints are used on material
thicknesses of:
sling load.
A small change in sling angle can
drastically affect the:
DC synergic, microprocessor-controlled.
The power sources used for pulsed spray
transfer are:
3/8" -1" (9.5 -25.4mm)
Single "V" butt joints are used on material
thicknesses of:
If you must apply force to a suspended
load, always pull the load towards you.
Live side of the wire
When installing clips, the saddle side of the
clip must be placed on the:
1/4
When balancing a No. 2 welding tip and
the acetylene torch needle valve is fully
open, the acetylene regulator should be
adjusted so that the flame blows away from
the tip _______ inch. (Oxygen needle
valve is closed)
stainless
Which ferrous-based metals cannot be cut
satisfactorily with an oxy-fuel cutting torch?
240
What is the total number of hours in the
first period Welder Training Profile?
about 3 mm (1/8") above the surface.
When starting a cut on plate, the preheat
cones should be held:
