AUT 101 Fundamentals Final Exam Study Guide || A+
Graded Solutions.
The brake system uses friction to stop the vehicle -T/F correct answers true
The air conditioner is part of the vehicle's cooling system -T/F correct answers False
It is almost impossible to service anything on a car today without handling some type of
electrical or electronic component -T/F correct answers True
There are many automotive careers that do not require a great deal of mechanical ability -T/F
correct answers True
A technician can gain ASE Certification in more that one specialty area -T/F correct answers
True
An experienced and skilled auto technician is capable of performing tasks common to a
number of other trades. -T/F correct answers True
After Learning "the basics," a transmission technician seldom needs additional specialized
training -T/F correct answers False
When answering an ASE test question, analyze it as if you were the technician trying to fix
the car -T/F correct answers True
A magnetic pickup will attract any kind of metal -T/F correct answers False
If the head of a chisel or punch becomes "mushroomed," the tool must be discarded. -T/F
correct answers False
The 6-point box-end wrench should be used when a bolt head or nut is extremely tight -T/F
correct answers True
Torx screws have a square indentation in their heads. -T/F correct answers False
The tip of a pin punch should be ground flat and square -T/F correct answers False
For safety, battery charger leads must be connected to the battery after the charger is turned
on -T/F correct answers False
A wire wheel in a bench grinder should not be used to clean soft metal or brass parts. -T/F
correct answers True
Shop air pressure is seldom higher than 50 psi. -T/F correct answers False
Air-powered tools should always be lubricated before use. -T/F correct answers True
It is unsafe to work under a vehicle supported only by a jack. -T/F correct answers True
, A soldering iron or gun is heated by electricity. -T/F correct answers True
A sphyxiation is caused by breathing toxic substances in the air. -T/F correct answers True
Accidents Seldom result from breaking safety rules. -T/F correct answers False
The safety catch on a hydraulic lift must be engaged after you work under the vehcicle. -T/F
correct answers False
You should always have your instructor demonstrate potentially dangerous equipment before
you try to use it. -T/F correct answers True
Always pull vehicles through shop doors slowly and carefully to make sure they will clear the
bottom of the raised door. -T/F correct answers True
If you use power tools carefully, wearing eye protection usually is not necessary -T/F correct
answers False
Dust from brake shoes should be blown off parts with compressed air -T/F correct answers
False
An electric-powered tool should never be used unless the plug has a functional ground prong.
-T/F correct answers True
power tools must always be used with any safety guards in place. -T/F correct answers True
Illustrations are a nonessential part of a service manual -T/F correct answers False
The VIN is usually found on the dashboard -T/F correct answers True
A service manual is one of the technician's most important tools -T/F correct answers True
An exploded view showing how parts fit together is a common type of service manual
illustration. -T/F correct answers True
Sealer must always be used when installing a gasket -T/F correct answers False
A seal is used to prevent leakage between a stationary part and a moving part -T/F correct
answers True
The only way to remove a broken bolt is to drill it out. -T/F correct answers False
In automotive work, olts and nuts are often named after the parts they hold -T/F correct
answers True
When installing a gasket, all fasteners should be hand-tightened before a wrench is applied -
T/F correct answers True
An O-ring seal should never be exposed to oil or other engine fluids -T/F correct answers
True
Graded Solutions.
The brake system uses friction to stop the vehicle -T/F correct answers true
The air conditioner is part of the vehicle's cooling system -T/F correct answers False
It is almost impossible to service anything on a car today without handling some type of
electrical or electronic component -T/F correct answers True
There are many automotive careers that do not require a great deal of mechanical ability -T/F
correct answers True
A technician can gain ASE Certification in more that one specialty area -T/F correct answers
True
An experienced and skilled auto technician is capable of performing tasks common to a
number of other trades. -T/F correct answers True
After Learning "the basics," a transmission technician seldom needs additional specialized
training -T/F correct answers False
When answering an ASE test question, analyze it as if you were the technician trying to fix
the car -T/F correct answers True
A magnetic pickup will attract any kind of metal -T/F correct answers False
If the head of a chisel or punch becomes "mushroomed," the tool must be discarded. -T/F
correct answers False
The 6-point box-end wrench should be used when a bolt head or nut is extremely tight -T/F
correct answers True
Torx screws have a square indentation in their heads. -T/F correct answers False
The tip of a pin punch should be ground flat and square -T/F correct answers False
For safety, battery charger leads must be connected to the battery after the charger is turned
on -T/F correct answers False
A wire wheel in a bench grinder should not be used to clean soft metal or brass parts. -T/F
correct answers True
Shop air pressure is seldom higher than 50 psi. -T/F correct answers False
Air-powered tools should always be lubricated before use. -T/F correct answers True
It is unsafe to work under a vehicle supported only by a jack. -T/F correct answers True
, A soldering iron or gun is heated by electricity. -T/F correct answers True
A sphyxiation is caused by breathing toxic substances in the air. -T/F correct answers True
Accidents Seldom result from breaking safety rules. -T/F correct answers False
The safety catch on a hydraulic lift must be engaged after you work under the vehcicle. -T/F
correct answers False
You should always have your instructor demonstrate potentially dangerous equipment before
you try to use it. -T/F correct answers True
Always pull vehicles through shop doors slowly and carefully to make sure they will clear the
bottom of the raised door. -T/F correct answers True
If you use power tools carefully, wearing eye protection usually is not necessary -T/F correct
answers False
Dust from brake shoes should be blown off parts with compressed air -T/F correct answers
False
An electric-powered tool should never be used unless the plug has a functional ground prong.
-T/F correct answers True
power tools must always be used with any safety guards in place. -T/F correct answers True
Illustrations are a nonessential part of a service manual -T/F correct answers False
The VIN is usually found on the dashboard -T/F correct answers True
A service manual is one of the technician's most important tools -T/F correct answers True
An exploded view showing how parts fit together is a common type of service manual
illustration. -T/F correct answers True
Sealer must always be used when installing a gasket -T/F correct answers False
A seal is used to prevent leakage between a stationary part and a moving part -T/F correct
answers True
The only way to remove a broken bolt is to drill it out. -T/F correct answers False
In automotive work, olts and nuts are often named after the parts they hold -T/F correct
answers True
When installing a gasket, all fasteners should be hand-tightened before a wrench is applied -
T/F correct answers True
An O-ring seal should never be exposed to oil or other engine fluids -T/F correct answers
True
