FDNYC G60 PRACTICE EXAM
A Responsible Person is one who is - ANSWERS-trained in the fire safety hazards
associated with hot work, and in the necessary and appropriate measures to
minimize those hazards, who is designated by the owner of a premises to
authorize the performance of hot work at the premises.
A designated Hot Work area must be at least_______ feet away from combustible
materials. - ANSWERS-35.
For all Hot Work, inspections must be completed_______ after completion of
torch operations. - ANSWERS-30 minutes.
A minimum ___________ rating Fire Extinguisher must be readily accessible
within ________ of the hot work location for torch operations. - ANSWERS-2-
A:20-B:C, 30 feet.
For a Torch-applied Roof System, a minimum ___________ rating Fire
Extinguisher must be readily accessible within ________. - ANSWERS-3-A: 40-B:C,
30 feet.
Empty compressed gas cylinders - ANSWERS-Should be handled in the same
manner as full ones.
, Panic Bar - ANSWERS-A device fitted on the inside of a door that would allow a
person to push against a door to open it.
A type of valve typically used in sprinkler systems - ANSWERS-OS & Y Valve-
Outside Screw and Yoke Valve.
Fire Drill - ANSWERS-A training exercise by which building occupants are
familiarized with and/ or practice the procedures for the safe, orderly and
expeditious in-building relocation, partial evacuation or evacuation, as applicable
to the occupancy or building type, in accordance with the fire safety and
evacuation plan.
shall not be considered a fire - ANSWERS-flame used in any lawful, properly
operating device, equipment or system or other controlled setting.
Fire Watch - ANSWERS-A temporary measure intended to ensure continuous and
systematic surveillance of a building or portion thereof by one or more qualified
individuals for the purposes of identifying and controlling fire hazards, detecting
early signs of fire, raising an alarm of fire and notifying the department.
Hot Work - ANSWERS-Cutting, welding, thermit welding, brazing, soldering,
grinding, thermal spraying, thawing pipe, cad welding, installation of torch-
applied system, or any other similar operation or activity.
A Responsible Person is one who is - ANSWERS-trained in the fire safety hazards
associated with hot work, and in the necessary and appropriate measures to
minimize those hazards, who is designated by the owner of a premises to
authorize the performance of hot work at the premises.
A designated Hot Work area must be at least_______ feet away from combustible
materials. - ANSWERS-35.
For all Hot Work, inspections must be completed_______ after completion of
torch operations. - ANSWERS-30 minutes.
A minimum ___________ rating Fire Extinguisher must be readily accessible
within ________ of the hot work location for torch operations. - ANSWERS-2-
A:20-B:C, 30 feet.
For a Torch-applied Roof System, a minimum ___________ rating Fire
Extinguisher must be readily accessible within ________. - ANSWERS-3-A: 40-B:C,
30 feet.
Empty compressed gas cylinders - ANSWERS-Should be handled in the same
manner as full ones.
, Panic Bar - ANSWERS-A device fitted on the inside of a door that would allow a
person to push against a door to open it.
A type of valve typically used in sprinkler systems - ANSWERS-OS & Y Valve-
Outside Screw and Yoke Valve.
Fire Drill - ANSWERS-A training exercise by which building occupants are
familiarized with and/ or practice the procedures for the safe, orderly and
expeditious in-building relocation, partial evacuation or evacuation, as applicable
to the occupancy or building type, in accordance with the fire safety and
evacuation plan.
shall not be considered a fire - ANSWERS-flame used in any lawful, properly
operating device, equipment or system or other controlled setting.
Fire Watch - ANSWERS-A temporary measure intended to ensure continuous and
systematic surveillance of a building or portion thereof by one or more qualified
individuals for the purposes of identifying and controlling fire hazards, detecting
early signs of fire, raising an alarm of fire and notifying the department.
Hot Work - ANSWERS-Cutting, welding, thermit welding, brazing, soldering,
grinding, thermal spraying, thawing pipe, cad welding, installation of torch-
applied system, or any other similar operation or activity.
