PLTW ENGINEERING ESSENTIALS
EXAM NEWEST 2024 ACTUAL EXAM
COMPLETE 150 QUESTIONS AND
CORRECT DETAILED ANSWERS
(VERIFIED ANSWERS) | ALREADY
GRADED A+
The amount of overlap that one part has with another
when assembled
A. interference
B. allowance
C. tolerance
D. limit dimensions Correct Answer A. interference
A(n) _________________sketch provides additional
written information to clarify the details of a design..
A. pictorial
B. isometric
C. annotated
D. perspective Correct Answer C. annotated
What technique would be used in sketching to increase
clarity and improve artistic appearance?
A. painting
B. detailing
,C. exploding
D. rendering Correct Answer C. exploding
Two points that share the same location on a 2D sketch
are said to be______________.
A. coincident
B. collinear
C. concentric
D. coplanar Correct Answer A. coincident
Study the graphic below and answer the following
question.
What are the relative coordinates of POINT B with respect
to Point A?
A. (3,5)
B. (3,2)
C. (2,3)
D. (5,3) Correct Answer C. (2,3)
__________ and/or dimensions are necessary to fully
constrain a sketch when creating solid models.
A. 2D geometric constraints
B. formulas
C. parameters
D. offsets Correct Answer A. 2D geometric constraints
9.25 yards is equivalent to
,A. 27 feet
B. 27.5 feet
C. 9 feet
D. 27.75 feet Correct Answer D. 27.75 feet
23,439 milliliters is equivalent to
A. 234.39 liters
B. 2.3439 liters
C. 23.439 liters
D. .023439 liters Correct Answer C. 23.439 liters
A private, non-profit organization that coordinates the
development and use of a voluntary consensus standards
in the United States.
A. American Society of Mechanical Engineers (ASME)
B. International Organization for Standardizations (IOS)
C. Occupational Safety and Hazard Association (OSHA)
D. American National Standards Institute (ANSI) Correct
Answer D. American National Standards Institute (ANSI)
A view that is used to show features that is located on an
inclined surface in true size and shape.
A. Detail View
B. Auxiliary View
C. Section View
D. Cutting Plane Line Correct Answer B. Auxiliary View
67.5 centimeters is equivalent to
, A. 171.45 inches
B. 26.57 inches
C. 100 inches
D. 2 feet Correct Answer B. 26.57 inches
A view that is used to show a magnified view of features
that are too small to adequately specify in another view.;
A. Detail View
B. Auxiliary View
C. Section View
D. Cutting Plane Line Correct Answer A. Detail View
Why is placement of your dimensions so important?
A. To reduce tolerance problems
B. To reduce confusion
C. It does not matter
D. None of the above Correct Answer B. To reduce
confusion
A graph of vertical bars representing the frequency
distribution of a set of data is called
A. bar graph
B. histogram
C. line graph
D. distribution graph Correct Answer B. histogram
EXAM NEWEST 2024 ACTUAL EXAM
COMPLETE 150 QUESTIONS AND
CORRECT DETAILED ANSWERS
(VERIFIED ANSWERS) | ALREADY
GRADED A+
The amount of overlap that one part has with another
when assembled
A. interference
B. allowance
C. tolerance
D. limit dimensions Correct Answer A. interference
A(n) _________________sketch provides additional
written information to clarify the details of a design..
A. pictorial
B. isometric
C. annotated
D. perspective Correct Answer C. annotated
What technique would be used in sketching to increase
clarity and improve artistic appearance?
A. painting
B. detailing
,C. exploding
D. rendering Correct Answer C. exploding
Two points that share the same location on a 2D sketch
are said to be______________.
A. coincident
B. collinear
C. concentric
D. coplanar Correct Answer A. coincident
Study the graphic below and answer the following
question.
What are the relative coordinates of POINT B with respect
to Point A?
A. (3,5)
B. (3,2)
C. (2,3)
D. (5,3) Correct Answer C. (2,3)
__________ and/or dimensions are necessary to fully
constrain a sketch when creating solid models.
A. 2D geometric constraints
B. formulas
C. parameters
D. offsets Correct Answer A. 2D geometric constraints
9.25 yards is equivalent to
,A. 27 feet
B. 27.5 feet
C. 9 feet
D. 27.75 feet Correct Answer D. 27.75 feet
23,439 milliliters is equivalent to
A. 234.39 liters
B. 2.3439 liters
C. 23.439 liters
D. .023439 liters Correct Answer C. 23.439 liters
A private, non-profit organization that coordinates the
development and use of a voluntary consensus standards
in the United States.
A. American Society of Mechanical Engineers (ASME)
B. International Organization for Standardizations (IOS)
C. Occupational Safety and Hazard Association (OSHA)
D. American National Standards Institute (ANSI) Correct
Answer D. American National Standards Institute (ANSI)
A view that is used to show features that is located on an
inclined surface in true size and shape.
A. Detail View
B. Auxiliary View
C. Section View
D. Cutting Plane Line Correct Answer B. Auxiliary View
67.5 centimeters is equivalent to
, A. 171.45 inches
B. 26.57 inches
C. 100 inches
D. 2 feet Correct Answer B. 26.57 inches
A view that is used to show a magnified view of features
that are too small to adequately specify in another view.;
A. Detail View
B. Auxiliary View
C. Section View
D. Cutting Plane Line Correct Answer A. Detail View
Why is placement of your dimensions so important?
A. To reduce tolerance problems
B. To reduce confusion
C. It does not matter
D. None of the above Correct Answer B. To reduce
confusion
A graph of vertical bars representing the frequency
distribution of a set of data is called
A. bar graph
B. histogram
C. line graph
D. distribution graph Correct Answer B. histogram
