BMW Associate Level ASE Latest Test Exam
Written With Accurate Answers 2026
A lifting pad must be in place to lift a BMW vehicle, T or F? Correct Answer True
A technician should consider which of the following questions for a quality control process after
performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above Correct Answer All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown
represents Correct Answer Acute toxicity
All BMW special tools are autoship to the dealer.
True or False? Correct Answer False
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device.
Correct Answer Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz Correct Answer The Roundtable is accessed through AIR.
Battery voltage is not critical when performing a voltage drop on a circuit.
, True or False? Correct Answer Flase
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? Correct Answer
Owners Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure Correct Answer Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in
the tread. T or F? Correct Answer False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad
and 7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
Who is correct? Correct Answer Neither A or B
During a CPO inspection, all of the following items will need to be addressed before the CPO
sale, EXCEPT:
Mismatched tires
Aftermarket windshield
OEM brake pads with 4mm thickness of material remaining
Wheel with a lateral runout of 1.2mm Correct Answer Aftermarket windshield
During a CPO inspection, which of the following will irreversibly disqualify a vehicle from the
CPO program:
Written With Accurate Answers 2026
A lifting pad must be in place to lift a BMW vehicle, T or F? Correct Answer True
A technician should consider which of the following questions for a quality control process after
performing service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above Correct Answer All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown
represents Correct Answer Acute toxicity
All BMW special tools are autoship to the dealer.
True or False? Correct Answer False
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device.
Correct Answer Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz Correct Answer The Roundtable is accessed through AIR.
Battery voltage is not critical when performing a voltage drop on a circuit.
, True or False? Correct Answer Flase
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? Correct Answer
Owners Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure Correct Answer Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in
the tread. T or F? Correct Answer False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad
and 7mm on the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
Who is correct? Correct Answer Neither A or B
During a CPO inspection, all of the following items will need to be addressed before the CPO
sale, EXCEPT:
Mismatched tires
Aftermarket windshield
OEM brake pads with 4mm thickness of material remaining
Wheel with a lateral runout of 1.2mm Correct Answer Aftermarket windshield
During a CPO inspection, which of the following will irreversibly disqualify a vehicle from the
CPO program:
