VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
1. Enter and proceed" is presented as a ________ on the c. Circle
raised touchable surface on a function key."
a. Triangle
b. Double Line
c. Circle
d. Dotted Line
2. In new buildings, thresholds at doorways should be a. 1/2"
no higher than ________.
a. 1/2"
b. 1-1/4"
c. 3/4"
d. 1/4"
3. The maximum knee clearance shall be permitted to d. 25"
extend _____ under an element that is 9" above the
floor.
a. 30"
b. 18"
c. 36"
d. 25"
4. In existing buildings and facilities, the turning space a. 60-inch
shall be a circular space with a _____ minimum diame-
ter.
a. 60-inch
b. 50-inch
c. 70-inch
d. 55-inch
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
5. The brightness of the elevator car landing sill, thresh- d. 5
old platform and controls are to be no less than _______
foot candles.
a. 15
b. 10
c. 54
d. 5
6. The clear width of an exterior accessible route located c. 36 inches
within seating areas shall be _____ minimum.
a. 42 inches
b. 48 inches
c. 36 inches
d. 32 inches
7. In a Type A unit, if measuring to the highest part of b. 34"
the rim or highest part of the counter, what is the
maximum height of the sink front above the floor?
a. 28"
b. 34"
c. 36"
d. 32"
8. What is the least diameter of grab bars with circular c. 1-1/4"
cross sections?
a. 1"
b. 2"
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
c. 1-1/4"
d. 1-1/2"
9. All hardware such as handles, locks, or any other op- b. 34"
erable parts shall be _____ minimum above the floor.
a. 30"
b. 34"
c. 36"
d. 20"
10. What is the minimum diameter of a circular turn- a. 67"
around area in a new building.
a. 67"
b. 47"
c. 20"
d. 50"
11. What components shall not be part of an accessible c. Revolving doors & Turn-
route stiles
a. Elevators & Platform Lifts
b. Blended Transitions
c. Revolving doors & Turnstiles
d. Gates & Curb Ramps
12. The maximum height of existing elevator call buttons c. 54"
shall be permitted to be located ____ above the floor.
a. 45"
b. 48"
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
c. 54"
d. 42"
13. In new construction, what is the maximum slope of a a. 1 : 12
ramp?
a. 1 : 12
b. 1 : 10
c. 1 : 8
d. 1 : 20
14. Doorways shall have a clear opening width of 32 inch- c. 4 inches
es minimum. Projections into the clear opening width
between 34 inches and 80 inches above the floor shall
not exceed:
a. 3 inches
b. 2 inches
c. 4 inches
d. 5 inches
15. The running slope of walking surfaces shall not be d. 1 : 20
steeper than:
a. 1 : 12
b. 1 : 48
c. 1 : 8
d. 1 : 20
16. In existing buildings and facilities, the clear width of a a. 32 inches.
walking surface shall be permitted to be reduced to
_____ minimum for a length of 24 inches maximum.
Study online at https://quizlet.com/_hqa4z6
1. Enter and proceed" is presented as a ________ on the c. Circle
raised touchable surface on a function key."
a. Triangle
b. Double Line
c. Circle
d. Dotted Line
2. In new buildings, thresholds at doorways should be a. 1/2"
no higher than ________.
a. 1/2"
b. 1-1/4"
c. 3/4"
d. 1/4"
3. The maximum knee clearance shall be permitted to d. 25"
extend _____ under an element that is 9" above the
floor.
a. 30"
b. 18"
c. 36"
d. 25"
4. In existing buildings and facilities, the turning space a. 60-inch
shall be a circular space with a _____ minimum diame-
ter.
a. 60-inch
b. 50-inch
c. 70-inch
d. 55-inch
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
5. The brightness of the elevator car landing sill, thresh- d. 5
old platform and controls are to be no less than _______
foot candles.
a. 15
b. 10
c. 54
d. 5
6. The clear width of an exterior accessible route located c. 36 inches
within seating areas shall be _____ minimum.
a. 42 inches
b. 48 inches
c. 36 inches
d. 32 inches
7. In a Type A unit, if measuring to the highest part of b. 34"
the rim or highest part of the counter, what is the
maximum height of the sink front above the floor?
a. 28"
b. 34"
c. 36"
d. 32"
8. What is the least diameter of grab bars with circular c. 1-1/4"
cross sections?
a. 1"
b. 2"
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
c. 1-1/4"
d. 1-1/2"
9. All hardware such as handles, locks, or any other op- b. 34"
erable parts shall be _____ minimum above the floor.
a. 30"
b. 34"
c. 36"
d. 20"
10. What is the minimum diameter of a circular turn- a. 67"
around area in a new building.
a. 67"
b. 47"
c. 20"
d. 50"
11. What components shall not be part of an accessible c. Revolving doors & Turn-
route stiles
a. Elevators & Platform Lifts
b. Blended Transitions
c. Revolving doors & Turnstiles
d. Gates & Curb Ramps
12. The maximum height of existing elevator call buttons c. 54"
shall be permitted to be located ____ above the floor.
a. 45"
b. 48"
, VA HIC Exam Prep
Study online at https://quizlet.com/_hqa4z6
c. 54"
d. 42"
13. In new construction, what is the maximum slope of a a. 1 : 12
ramp?
a. 1 : 12
b. 1 : 10
c. 1 : 8
d. 1 : 20
14. Doorways shall have a clear opening width of 32 inch- c. 4 inches
es minimum. Projections into the clear opening width
between 34 inches and 80 inches above the floor shall
not exceed:
a. 3 inches
b. 2 inches
c. 4 inches
d. 5 inches
15. The running slope of walking surfaces shall not be d. 1 : 20
steeper than:
a. 1 : 12
b. 1 : 48
c. 1 : 8
d. 1 : 20
16. In existing buildings and facilities, the clear width of a a. 32 inches.
walking surface shall be permitted to be reduced to
_____ minimum for a length of 24 inches maximum.
