Freshy

NHCO Phlebotomy Another name for phlebotomy - Answer- Venipuncture Another name for finger stick - Answer- Dermal puncture Responsibilities of phlebotomist - Answer- Assembles equipment Verifies and records the patients identity Conducts patient interviews Takes vital signs Screens donors Patient interaction characteristics - Answer- Dependability Honesty Integrity Empathy and compassion Professional appearance Interpersonal skills How to positively identify patient - Ans...

Ohio stationary steam engineer Combustion efficiency may be increased by_____ the primary air - Answer- Preheating What is the purpose of cinder reinjection? - Answer- increase efficiency 2 forces of equal intensity acting in opposite directions is? - Answer- tension What is true about the dew poimt of flue gasses - Answer- dew point is the temp at which the gasses will condense What will not cause high stack temps? - Answer- plugged dry pipe What is true about smoke - Answer- ...

All of Engineering 2024 part 3 Electron - Answer- an extremely small negatively charged subatomic particle that orbits the nucleus of an atom Element - Answer- a substance that is composed of only one type of atom and cannot be broken down by chemical means into a simpler form Energy - Answer- the ability to cause matter to move or transform Engineer - Answer- a person trained and skilled in the design and development of technological solutions to human problems Engineer's notebo...

Stationary Engineering Chapter 5.2-3 The fire point temperature is higher than the flash point temperature. - Answer- True Fuel oil characteristics include viscosity, pour point, flash point, fire point, volatility, and heating value. - Answer- True Atomization is the ability of fuel to be vaporized. - Answer- False The Btu rating of a fuel indicates how much heat it can produce - Answer- True A decrease in a suction gauge reading indicates either a dirty strainer or cold fuel oil...

Engineers License Study Guide secondary - Answer- What winding is connected to the load? Modulating pressure control - Answer- Regulates the steam pressure? when there is no pressure on the boiler - Answer- When can you blow down a water wall? purge - Answer- What must be done to prevent flashback? kinetic energy - Answer- Steam at a high velocity is converted into _ _ _ _ _ _ _ _ _ _engery? 3206 PSIA at 705.4°F - Answer- Supercritical pressure and saturation temperature? 8...

3rd class stationary steam engineer license prep _________ are necessary for complete combustion - Answer- time, temperature, mixture, and atomization if the steam pressure gauge indicates 200 PSIG, the absolute pressure is______ - Answer- 214.7 a boiler is operating at 400 PSI, and the safety valve opens at 410 PSI and closes at 398 PSI. The blowdown is______psi - Answer- 12 an oil cooler is commonly used with a(n) ________ when operating in conjunction with a turbo-generator - Answ...

Electrical Exam Study Guide 2024 Relays are generally used to control inductive loads up to ________ amps. - Answer- 10 Resistance is: - Answer- Opposition to current flow. One horsepower is equal to _______ watts - Answer- 746 When troubleshooting the A/C system in the schematic (during operation), the following conditions are found. The thermostat contacts are closed. The compressor and condenser fan motors are short cycling. The blower motor is not running. When the fan switch at ...

Grade 4 Stationary Engineer License Practice what is a boiler - Answer- a closed metal container (pressure vessel) which water is heated to produce steam or heated water what is steam - Answer- the vapor that forms when water is heated to its boiling point when did the greatest impact of the use of steam power occur - Answer- during the industrial revolution 18th and early 19th century who invented the steam engine and when - Answer- James Watt of Scotland in 1736 How is steam pro...

4 Stationary Engineer: Blue Seal, Final Practice Exam Operating pumps in a plant properly is a part of the operator's job. In the sketch below what would the pressure of the pump discharge pressure be at "C" for the sp. gr. shown and the feet conditions indicated? - Answer- The discharge pressure would be 35 psi By N.J.A.C. 12:90, a person holding a 1-C license, my act as a chief engineer of what type and capacity plant? - Answer- A high-pressure plant of 1,000 BHP, A low-pressure plant...

Stationary Engineer Exam Part 2 A low pressure steam boiler has a maximum allowable working pressure (MAWP) of up to___ - Answer- 15 psi. In a firetube boiler, the heat and gases of combustion pass ___ - Answer- Through the tubes A firetube boiler may be used _____ - Answer- In high or low pressure plants Because of the large volume of water, the boiler most likely to cause a boiler explosion is - Answer- A firetube boiler A horizontal return tubular (HRT) boiler is a _____ boiler...

Stationary Engineer Boiler Exam Pressure gauges should never have a range less than A. half the safety valve set pressure. B. double the safety valve set pressure. C. 3/4 times the safety valve set pressure. D. 1 1/2 times the safety valve set pressure. - Answer- D. 1 1/2 times the safety valve set pressure. After water is blown out of a siphon, why should live steam never be allowed to enter a Bourdon tube? A. The steam will rupture the siphon tube. B. Combustion gases will mix with...

1st Class Stationary Engineers Exam All Boilers should be viewed as - Answer- Dangerous regardless of size and pressure One cubic inch of hot water under pressure expands to - Answer- almost one cubic foot of steam at atmospheric pressure Primary air is usually... - Answer- Blown into the combustion chamber, along with the fuel on a gas or oil burner. Heat always flows from ____ to ____ - Answer- hot to cold An accumulation test is used to determine - Answer- the relieving capacit...

Stationary Engineer A test cavitation - Answer- what occurs when the fluid pressure equals the vapor pressure at the existing temperature, and as a result vapor bubbles alternately form and collapse? lifting pressure of a safety valve - Answer- a boiler accumulation test measures what? titration - Answer- most chemical testing is done by what method? control device - Answer- which of the following regulates the flow of a control agent in a system? relighting an extinguished fire w...

Stationary Engineer Electric An AC circuit consists only of a pure inductance and a power source. The relationship between the voltage and the current in this circuit is that the - Answer- current lags the voltage The power factor of a load is equal to the ____________ power divided by the ____________ power. - Answer- True ; apparent A 10-ohms and 20-ohms resistor are connected in parallel. The total line current drawn by this parallel combination is 30 amps. Under these conditions, th...

AutoCAD Draft and Design Professional Certification Refer to the exhibit. Blocks not being used in a drawing can be tidied up using the PURGE command, as shown in the exhibit. Which option allows you to check sequentially which blocks are being purged from the drawing? - Answer- C- Confirm Each Item to be purged A rectangular boundary encloses a landscaping layout represented by a number of geometric objects. When hatching, the hatch pattern covers all of the objects within the boundary. W...

Autocad Final Exam 1/4 - Answer- .25 3/8 - Answer- .375 7/16 - Answer- .4357 5/8 - Answer- .625 3/4 - Answer- .625 The language of sketching has four basic visual symbols are? - Answer- Plane,point,line Freehand sketching is the....................form of drawing? - Answer- Simplest In lettering............................means arranging words. - Answer- Composition When lettering by hand you may use two different style strokes,inclined and - Answer- Verticle There ...

AutoCAD Certification By default, AutoCAD has the following workspaces. - Answer- - 2D Drafting & Annotation - 3D Modeling - AutoCAD Classic Object snap tracking works in combination with object snaps to enable you to temporarily acquire & track up to how many points? - Answer- Seven Which of the following settings can be made for polar tracking? - Answer- - Increment Angle - Additional Angles If you need the text to be reversed, when you mirror the text, then you need to set: - A...

Autodesk Certified Professional in AutoCAD for Design and Drafting Exam Study Set Which method allows multiple grips to be selected simultaneously? - Answer- Select them while holding down the Shift key. When grip editing an object with dynamic input enabled, what does the small lock icon next to the highlighted value indicate? - Answer- The object is constrained by a previously entered value. When drawing a line with dynamic input enabled, how do you toggle between the displayed values...

AutoCAD EXAM 1 Current Layer - Answer- layer which objects being created are placed on Delete (Layer) - Answer- Removes a layer only if its empty Freeze/Thaw (Layer) - Answer- Affects how the element is displayed on the selected layer Layer - Answer- Used to separate and control elements of a drawing Layer Properties - Answer- Adjust color, line-types, line weights Lock/Unlock - Answer- elements of drawing can be viewed but not edited Make (Layers) - Answer- can create singl...

Autocad Certification Study Guide By default, AutoCAD has the following workspaces - Answer- 2D Drafting & Annotation 3D Modelin AutoCAD Classic Which Key do you press to cycle through the available snap points? - Answer- Tab One of the below options is wrong about type of Autocad drawing units. Which one is it? - Answer- Millimeter Object snap tracking works in combination with object snaps to enable you to temporarily acquire and track up to how many points? - Answer- 7 Which...