ARCH 331 MIDTERM Exam Questions And Answers With Verified Solutions 2025
Football Stadium: What is the typical material specification for W-shapes (hint reference General
Notes)? - ✔✔ASTM A992
Structural Steel Church Facility - Steel Building - What is the size of the column at G/5? - ✔✔W10x60
Structural Steel Church Facility - Steel Building - How many and what size vertical reinforcement is
required in a 30/54 belled (drilled and undereamed) pier? - ✔✔(5) - #6
Structural Steel Church Facility - What is the height that column G/5 terminates (top of column)? -
✔✔26'-6"
Post tensioned flat plate - per the title block, these sheets were issued "For Construction" since they are
sealed - ✔✔False
Emergency Medical Services Building & Structural Steel Weld Symbols - What type of weld is most nearly
required for the bent beam per detail 4/S4.01 - ✔✔Bevel - CJP
Metal Building System - What size (diameter) anchor rods and how many are required for column B/3? -
✔✔(4) - 3/4"
Metal Building System - What is the roof pitch (slope) for the building? - ✔✔4 on 12
Metal Building System - What is the typical purlin size between grids 5 and 6? - ✔✔10x25Z14
Football Stadium - What is the total thickness of the composite slab at the Mezzanine level (Sheet
S2.42)? - ✔✔6 1/2"
Football Stadium - How many and what size bottom bars are required for the cantilever raker just above
the column, reference 15/S6.40? - ✔✔(6) - #9
, Concrete Tilt Wall - What is the typical panel reinforcement required in a panel without openings? -
✔✔#4 @ 12 on-center, each way located in center of wall
Concrete Tilt Wall - What size continuous angle is required at the top of the tilt wall panels to connect
the roof joists to the panels? (Reference Sheet S3-1) - ✔✔L3x3x1/4
Specifications - Concrete Forming and Accessories can be found in which division section of the
specifications "Project Manual"? - ✔✔03 1000
What grade of steel are the steel channels shown on S1.1? - ✔✔ASTM A36
The type of steel roof specified is most nearly... - ✔✔1.5B
At the roof corners (ref S0.0 Components and Cladding Zones), the roof deck requires how many
fasteners per 36" wide panel of roof deck? - ✔✔7
The roof design assumed what maximum rainwater ponding on the roof (note effects the design of the
drains and scupper). - ✔✔4"
On S1.1 along Grid C, from grid 4 to approximately 30' west, what is the thickness of the embed plate
that connected the channels to the top of the CMU wall as they extend over? - ✔✔3/4"
What is the depth of the Typical Grade Beam on S1.0? - ✔✔32"
What is the size of the steel column at the Pay Station Canopy? - ✔✔W8x58
What is the depth (thickness) of spread footing type F1 supporting the canopy columns? - ✔✔12"
What is the size of the bottom chord of the trusses at the High Roof? - ✔✔HSS6x6x1/4
Football Stadium: What is the typical material specification for W-shapes (hint reference General
Notes)? - ✔✔ASTM A992
Structural Steel Church Facility - Steel Building - What is the size of the column at G/5? - ✔✔W10x60
Structural Steel Church Facility - Steel Building - How many and what size vertical reinforcement is
required in a 30/54 belled (drilled and undereamed) pier? - ✔✔(5) - #6
Structural Steel Church Facility - What is the height that column G/5 terminates (top of column)? -
✔✔26'-6"
Post tensioned flat plate - per the title block, these sheets were issued "For Construction" since they are
sealed - ✔✔False
Emergency Medical Services Building & Structural Steel Weld Symbols - What type of weld is most nearly
required for the bent beam per detail 4/S4.01 - ✔✔Bevel - CJP
Metal Building System - What size (diameter) anchor rods and how many are required for column B/3? -
✔✔(4) - 3/4"
Metal Building System - What is the roof pitch (slope) for the building? - ✔✔4 on 12
Metal Building System - What is the typical purlin size between grids 5 and 6? - ✔✔10x25Z14
Football Stadium - What is the total thickness of the composite slab at the Mezzanine level (Sheet
S2.42)? - ✔✔6 1/2"
Football Stadium - How many and what size bottom bars are required for the cantilever raker just above
the column, reference 15/S6.40? - ✔✔(6) - #9
, Concrete Tilt Wall - What is the typical panel reinforcement required in a panel without openings? -
✔✔#4 @ 12 on-center, each way located in center of wall
Concrete Tilt Wall - What size continuous angle is required at the top of the tilt wall panels to connect
the roof joists to the panels? (Reference Sheet S3-1) - ✔✔L3x3x1/4
Specifications - Concrete Forming and Accessories can be found in which division section of the
specifications "Project Manual"? - ✔✔03 1000
What grade of steel are the steel channels shown on S1.1? - ✔✔ASTM A36
The type of steel roof specified is most nearly... - ✔✔1.5B
At the roof corners (ref S0.0 Components and Cladding Zones), the roof deck requires how many
fasteners per 36" wide panel of roof deck? - ✔✔7
The roof design assumed what maximum rainwater ponding on the roof (note effects the design of the
drains and scupper). - ✔✔4"
On S1.1 along Grid C, from grid 4 to approximately 30' west, what is the thickness of the embed plate
that connected the channels to the top of the CMU wall as they extend over? - ✔✔3/4"
What is the depth of the Typical Grade Beam on S1.0? - ✔✔32"
What is the size of the steel column at the Pay Station Canopy? - ✔✔W8x58
What is the depth (thickness) of spread footing type F1 supporting the canopy columns? - ✔✔12"
What is the size of the bottom chord of the trusses at the High Roof? - ✔✔HSS6x6x1/4
