BIPC 620 EXAM with CORRECT
ANSWERS
Certified IPC Tainter CIT and Certified IPC Specialist certifications exipre
after how many years <correct answer>2 Years
Master IPC Trainers MIT are authorized to ceritfy <correct answer>CIT and
CIS only
A CIT is authorized to certify <correct answer>CIS
If permitted by company policy, a CIT may grant an extension of up to how
many days <correct answer>90 days
What module is required as a pre req. for IPC 620 CIS certification <correct
answer>Module 1
CIS retesting may be taken only after a minimum of <correct answer>24
hours
What is the correct order of production status <correct answer>Design,
PCB Fabrication, Assemly, Cleaning and Coating
The tolerance for magnification aid is <correct answer>Plus or Minus 15
(Chapter 1) Page 1-7
The Manufacturer shall (_1_2_3) have a documented calibration system
<correct answer>N1D2D3 - PAGE 1-8
What is a Process Indicator <correct answer>A condition that identifies a
characteristics that does not affect the form fit or function of a product-
should be monitored
, Conditions that are not specified as defective or as a process indicator are
considered <correct answer>Acceptable - Page 1-4
Illumination at the surface of workstation should be minimum of <correct
answer>1000 lm/m^ 2or 93foot candles
A condition that is close to perfect defines what type of condition <correct
answer>Target
When inspecting a 22 AWG wire the inspection magnification range shall
be <correct answer>1.5X-3X - Table 1-1
The criteria defined in IPC-620 reflect three product classes , Class 1, 2, 3
<correct answer>Class 1- General Electronic Products
Class 2- Dedicated Service Electronic Products
Class 3- High Performance/ Harsh Environment Electronic Products
If insulation thickness is reduced by more than 20%, the condition is
_1_2_3 <correct answer>Defect for all classes - Chapter 3 - page 3-9
Damaged wires that do not exceed the limits specified in table 3-1 are
considered _1_2_3 <correct answer>A1P2P3 so process indicators for 2
and 3 -Page 3-2
Wire separation that exceeds one strand diameter but does not extend
beyond the wire insulation outside diameter is _1_2_3 <correct
answer>A1P2D3 Chapter 3 page 3-6
The maximum number of damaged strands for Class 2 wires with 28
strands used at a potential of 6kV or greater is <correct answer>0 -
Chapter 3, refer to Table 3-1
Insulation that has been charred, melted into the wire strands and has
uneven or ragged pieces of insulation that is greater than 50% of the
outside diameter or 1 mm, is what for all classes <correct answer>Defect
ANSWERS
Certified IPC Tainter CIT and Certified IPC Specialist certifications exipre
after how many years <correct answer>2 Years
Master IPC Trainers MIT are authorized to ceritfy <correct answer>CIT and
CIS only
A CIT is authorized to certify <correct answer>CIS
If permitted by company policy, a CIT may grant an extension of up to how
many days <correct answer>90 days
What module is required as a pre req. for IPC 620 CIS certification <correct
answer>Module 1
CIS retesting may be taken only after a minimum of <correct answer>24
hours
What is the correct order of production status <correct answer>Design,
PCB Fabrication, Assemly, Cleaning and Coating
The tolerance for magnification aid is <correct answer>Plus or Minus 15
(Chapter 1) Page 1-7
The Manufacturer shall (_1_2_3) have a documented calibration system
<correct answer>N1D2D3 - PAGE 1-8
What is a Process Indicator <correct answer>A condition that identifies a
characteristics that does not affect the form fit or function of a product-
should be monitored
, Conditions that are not specified as defective or as a process indicator are
considered <correct answer>Acceptable - Page 1-4
Illumination at the surface of workstation should be minimum of <correct
answer>1000 lm/m^ 2or 93foot candles
A condition that is close to perfect defines what type of condition <correct
answer>Target
When inspecting a 22 AWG wire the inspection magnification range shall
be <correct answer>1.5X-3X - Table 1-1
The criteria defined in IPC-620 reflect three product classes , Class 1, 2, 3
<correct answer>Class 1- General Electronic Products
Class 2- Dedicated Service Electronic Products
Class 3- High Performance/ Harsh Environment Electronic Products
If insulation thickness is reduced by more than 20%, the condition is
_1_2_3 <correct answer>Defect for all classes - Chapter 3 - page 3-9
Damaged wires that do not exceed the limits specified in table 3-1 are
considered _1_2_3 <correct answer>A1P2P3 so process indicators for 2
and 3 -Page 3-2
Wire separation that exceeds one strand diameter but does not extend
beyond the wire insulation outside diameter is _1_2_3 <correct
answer>A1P2D3 Chapter 3 page 3-6
The maximum number of damaged strands for Class 2 wires with 28
strands used at a potential of 6kV or greater is <correct answer>0 -
Chapter 3, refer to Table 3-1
Insulation that has been charred, melted into the wire strands and has
uneven or ragged pieces of insulation that is greater than 50% of the
outside diameter or 1 mm, is what for all classes <correct answer>Defect
