ASE G1 Test Prep (General Automobile Maintenance) Study Guide GRADED A

True Toe can cause tire wear if not within manufacturer's specifications (True or False) True Camber can cause tire wear if not within manufacturer's specifications (True or False) False Caster can cause tire wear if not within manufacturer's specifications (True or False) Technician A only Technician A says that a PAX run-flat tire uses a special wheel. Technician B says that a standard tire can be used to replace a PAX run-flat tire. Which technician is correct ? Rear spacing Wheel back spacing is also called ? Load rating A tire is labeled 215/60R15 92T ; the 92 indicates what ? The shape of the flange area What do the letter "J J" mean in a wheel designation size labeled 14 x 7JJ Speed rating A tire is labeled 215/60R15 92T ; the T indicates what ? 10 mm When purchasing replacement tires, do not change tire width from the stock size by more than ? Fixed disc brake caliper Which type of disc brake caliper may leak brake fluid more often ? A Boiling Point Tester Brake fluid boiling point can be measured using ? Electromagnetic induction What principle is used to create high voltage from low voltage? The ratio of height to width The Aspect Ratio of a tire means what ? Ignition Module The pickup coil or trigger is usually electrically connected to the ? Sintering Semi-metallic brake pads are made by a process called ? Soot is being burned Which of these takes place during regeneration in a Diesel Particulate Filter (DPF)? Coefficient of Friction Rating The brake pad edge code letters "FF" mean what ? With the vehicle parked on level ground Engine oil level should be checked .... Low-Drag caliper A quick-take-up master cylinder is required when what type of caliper design is used on a vehicle ? Glow plug or injector What part should be removed to test cylinder compression on a diesel engine? Technician B only Technician A says that maintenance-free batteries use a large amount of water. Technician B says that maintenance-free batteries use materials that reduce the amount of water used by the battery. Which technician is correct? The Square-Cut O-ring What part causes the disc brake caliper piston to retract when the brakes are released ? Embittered Adding a chemical to make ethylene glycol bitter to the taste is called ? ANSI (American National Standards Institute) All safety glasses should meet standards set by ? Throttle Position Sensor (TPS) A potentiometer, a three-wire variable resistor, is used in which type of sensor? Technician B only Technician A says that galvanic activity is the result of a poor ground connection. Technician B says that electrolysis can occur with a poor ground connection. Which technician is correct? At the outlet of the fuel rail Where is the fuel-pressure regulator located on a vacuum-biased port fuel-injection system? Tendency of oil to resist flowing Oil viscosity indicates what ? Technician A only Technician A says that with self-adjusting clutch systems, the release bearing constantly rotates. Technician B says the ball bearing portion of the release bearing should be lubricated with high temperature grease during routine maintenance. Which technician is correct? 30 mph Hydroplaning can occur at speeds as low as ? Vibration Battery hold-down clamps or brackets help reduce ____________ , which can greatly reduce the capacity and life of any battery. Gear reduction A starter can be constructed in a smaller size due to the use of ________________ and permanent magnets. Both Technicians A and B Two technician are discussing the need for history of the vehicle. Technician A says that an accident could cause faults due to hidden damage. Technician B says that some faults could be related to a previous repair. Which technician is correct? Both Technicians A and B Technician A says the gear reduction occurs when the drive gear turns faster than the driven gear. Technician B says that overdrive occurs when the driven gear turns faster than the drive gear. Which technician is correct? Neither Technician A nor B Technician A says that the cooling system should be tested for leaks using a pressure-operated pressure pump. Technician B says that the freezing and boiling point of the coolant can be tested using a thermometer. Which technician is correct? Technician B only