Arizona Contractor License CR-67 Exam (Latest Exam
2026) || Most Recent Exam 2026-2027 Actual Complete
Real Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ | Guaranteed Success!!
Newest Exam | Just Released!!
For a low voltage configuration, the conductors to use for
appliance branch circuits that supply more than one appliance
should never be smaller than? - ANSWER-10 AWG copper (or
equivalent)
For a low voltage configuration, standard lampholders with a
rating less than
_______ watts should not be used. -
ANSWER-660 W
Even in a low voltage configuration, the receptacles of less than
______ ampere rating should not be used in kitchens where
portable appliances will be deployed. - ANSWER-20 -ampere
Even in a low voltage configuration, the receptacles of less than
_________ ampere rating should not be used in laundries where
portable appliances will be deployed. - ANSWER-20 -ampere
Even in a low voltage configuration, cables should be
supported by? -
,ANSWER-The building
structure.
A Class 1 Circuit stays between? - ANSWER-The load side of
the overcurrent
device and the connected
equipment.
Whenever practicable, communications wires and cable
should be located
_______ electric light or power conductors. -
ANSWER-Below.
You should not allow communications wires to be attached to
a cross-arm if? -
ANSWER-the cross-arm carries electric power
conductors.
At the roof, you need to give communications cables a
minimum vertical clearance of _______ feet from the points
above which they pass. - ANSWER-8 feet
A class _____ Circuit stays between the load side of a Class
2 power source
and a connected equipment. -
ANSWER-2 Circuit
Remote -control circuits for use with safety - control equipment
are considered
,Class _____ if failure to operate can introduce direct fire
of life hazard. -
ANSWER-
1
Class 1 power -Limited Circuits should be supplied from a
source that has a
rated output of ______ volts or below only. -
ANSWER-30 volts
A class ______ circuits always considers safety from a fire
initiation standpoint.
- ANSWER-2
circuits
Class 1 Power Sources other than transformers should have
protection from overcurrent devices rated at max ______ of the
volt -- ampere rating of the source divided by the rated voltage.
- ANSWER-167%
A Class ______ circuit permits higher voltage than a class 2
circuit. - ANSWER-
3
circuit
________ refers to the max volts - ampere output after a single
minute of operation disregarding load and overcurrent
protection. - ANSWER-VAmax
, _______ refers to the max output current under any
noncapacitive load and with
overcurrent protection skipped. -
ANSWER-Imax
Class 1 Remote -Control and Signaling Circuits should
never exceed. -
ANSWER-600
volts
A Class 3 circuit always considers safety from a fire
initiation standpoint -
ANSWER-
True
Cables and conductors of class 2 and class 3 circuits should
not be placed in a
cable tray with conductors of electric light. -
ANSWER-True
Any accessible portion of abandoned Class 2 cables. -
ANSWER-Should be
removed
The power output of the source of Class 1 Remote - Control and
Signaling Circuit. - ANSWER-Class 1 Remote - Control and
Signaling Circuits are NOT required to be limited
2026) || Most Recent Exam 2026-2027 Actual Complete
Real Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ | Guaranteed Success!!
Newest Exam | Just Released!!
For a low voltage configuration, the conductors to use for
appliance branch circuits that supply more than one appliance
should never be smaller than? - ANSWER-10 AWG copper (or
equivalent)
For a low voltage configuration, standard lampholders with a
rating less than
_______ watts should not be used. -
ANSWER-660 W
Even in a low voltage configuration, the receptacles of less than
______ ampere rating should not be used in kitchens where
portable appliances will be deployed. - ANSWER-20 -ampere
Even in a low voltage configuration, the receptacles of less than
_________ ampere rating should not be used in laundries where
portable appliances will be deployed. - ANSWER-20 -ampere
Even in a low voltage configuration, cables should be
supported by? -
,ANSWER-The building
structure.
A Class 1 Circuit stays between? - ANSWER-The load side of
the overcurrent
device and the connected
equipment.
Whenever practicable, communications wires and cable
should be located
_______ electric light or power conductors. -
ANSWER-Below.
You should not allow communications wires to be attached to
a cross-arm if? -
ANSWER-the cross-arm carries electric power
conductors.
At the roof, you need to give communications cables a
minimum vertical clearance of _______ feet from the points
above which they pass. - ANSWER-8 feet
A class _____ Circuit stays between the load side of a Class
2 power source
and a connected equipment. -
ANSWER-2 Circuit
Remote -control circuits for use with safety - control equipment
are considered
,Class _____ if failure to operate can introduce direct fire
of life hazard. -
ANSWER-
1
Class 1 power -Limited Circuits should be supplied from a
source that has a
rated output of ______ volts or below only. -
ANSWER-30 volts
A class ______ circuits always considers safety from a fire
initiation standpoint.
- ANSWER-2
circuits
Class 1 Power Sources other than transformers should have
protection from overcurrent devices rated at max ______ of the
volt -- ampere rating of the source divided by the rated voltage.
- ANSWER-167%
A Class ______ circuit permits higher voltage than a class 2
circuit. - ANSWER-
3
circuit
________ refers to the max volts - ampere output after a single
minute of operation disregarding load and overcurrent
protection. - ANSWER-VAmax
, _______ refers to the max output current under any
noncapacitive load and with
overcurrent protection skipped. -
ANSWER-Imax
Class 1 Remote -Control and Signaling Circuits should
never exceed. -
ANSWER-600
volts
A Class 3 circuit always considers safety from a fire
initiation standpoint -
ANSWER-
True
Cables and conductors of class 2 and class 3 circuits should
not be placed in a
cable tray with conductors of electric light. -
ANSWER-True
Any accessible portion of abandoned Class 2 cables. -
ANSWER-Should be
removed
The power output of the source of Class 1 Remote - Control and
Signaling Circuit. - ANSWER-Class 1 Remote - Control and
Signaling Circuits are NOT required to be limited
