age 1 of 39
MILLWRIGHT PRACTICE TEST STUDY GUIDE 2025/2026
COMPLETE QUESTIONS BANK AND CORRECT
DETAILED ANSWERS WITH RATIONALES || 100%
GUARANTEED PASS <LATEST VERSION>
If the seal was not properly aligned or there is excessive wear
in some bearing or shaft______ wear tracks will be the
indicator. ......ANSWER........Unusual
For removing hard to remove gasket materials found on sealing
surfaces ______ is recommended. ......ANSWER........sharpened
brass putty knife
Apprenticeship training is ......ANSWER........Conducted on the job
Charting alignment on a graph requires a chart that is divided
into thousandths of an inch vertically for the indicator readings
,age 2 of 39
and into whole inches horizontally for the _______
measurements. ......ANSWER........Distance
The orthographic drawing may contain a dash or ______ line
......ANSWER........Hidden
In order to shoot through a test object and project an image
onto a detector sheet or film radiography used as a source of
penetrating _____. ......ANSWER........Radiation
Which of the following task would you not perform with
dividers? ......ANSWER........Measure angles
The overspeed trip device is actuated when the turbine reaches
a predetermined limit usually _______ percent above normal
full load speed ......ANSWER........10
,age 3 of 39
Positive results in an offset measurement mean that the MTBM is
______ or on the 3 o'clock side ......ANSWER........High
Coupling gap is set and then there is measured
......ANSWER........Offset misalignment
In a hydraulic system movement depends on
......ANSWER........Pressure
Fractional dimensions are used on objects ____
......ANSWER........Such as furniture or utility items
If the cause of the problem is not immediately understood the
process of _____ is often the procedure of choice
......ANSWER........Elimination
, age 4 of 39
When applying sealant to the sealing glands flanges keep the
sealant away from the inside edges of the flange by at least
_______ inch ......ANSWER........3/16
A stroboscope is triggered by _______
......ANSWER........Transducer
The page of threaded fasteners is measured with a ______
gauge. ......ANSWER........Thread
Liquid penetrant highlights flaws in reveals ______.
......ANSWER........Surface cracks
The tool used to cut external threads on a boat or rod is a____
......ANSWER........Die
A bill of materials may include information on ______ and other
reference information ......ANSWER........Special processes
MILLWRIGHT PRACTICE TEST STUDY GUIDE 2025/2026
COMPLETE QUESTIONS BANK AND CORRECT
DETAILED ANSWERS WITH RATIONALES || 100%
GUARANTEED PASS <LATEST VERSION>
If the seal was not properly aligned or there is excessive wear
in some bearing or shaft______ wear tracks will be the
indicator. ......ANSWER........Unusual
For removing hard to remove gasket materials found on sealing
surfaces ______ is recommended. ......ANSWER........sharpened
brass putty knife
Apprenticeship training is ......ANSWER........Conducted on the job
Charting alignment on a graph requires a chart that is divided
into thousandths of an inch vertically for the indicator readings
,age 2 of 39
and into whole inches horizontally for the _______
measurements. ......ANSWER........Distance
The orthographic drawing may contain a dash or ______ line
......ANSWER........Hidden
In order to shoot through a test object and project an image
onto a detector sheet or film radiography used as a source of
penetrating _____. ......ANSWER........Radiation
Which of the following task would you not perform with
dividers? ......ANSWER........Measure angles
The overspeed trip device is actuated when the turbine reaches
a predetermined limit usually _______ percent above normal
full load speed ......ANSWER........10
,age 3 of 39
Positive results in an offset measurement mean that the MTBM is
______ or on the 3 o'clock side ......ANSWER........High
Coupling gap is set and then there is measured
......ANSWER........Offset misalignment
In a hydraulic system movement depends on
......ANSWER........Pressure
Fractional dimensions are used on objects ____
......ANSWER........Such as furniture or utility items
If the cause of the problem is not immediately understood the
process of _____ is often the procedure of choice
......ANSWER........Elimination
, age 4 of 39
When applying sealant to the sealing glands flanges keep the
sealant away from the inside edges of the flange by at least
_______ inch ......ANSWER........3/16
A stroboscope is triggered by _______
......ANSWER........Transducer
The page of threaded fasteners is measured with a ______
gauge. ......ANSWER........Thread
Liquid penetrant highlights flaws in reveals ______.
......ANSWER........Surface cracks
The tool used to cut external threads on a boat or rod is a____
......ANSWER........Die
A bill of materials may include information on ______ and other
reference information ......ANSWER........Special processes
