AZ ROC KB-1
ANS-Class B materials are required for hall wall finishes in a building that is nonspinkled and
has Group B occupancy. Typically, a joist girder isn't always ANS-Bridged. A lintel must have not
less than what number of inches of bearing over the ends of every jamb? - ANS-4 inches
A clean cowl of _____ inches is needed for more than a few eleven reinforcing metal bar in a
precast wall this is exposed to the elements - ANS-three/4. According to code, the subsequent
is NOT considered a dangerous vicinity for the reason of glazing: - ANS-Glazing in egress
window
According to the Americans with Disabilities Act, how massive does the landing need to be at
the lowest of a ramp? - ANS-3 toes by 5 toes
All of the subsequent roofing substances may be re-used except - ANS-combination materials
All of the following soil provisions are considered expansive except for: - ANS-at least 10% of
soil debris are much less than 5 micrometers in length
As the temperature of the concrete mix increases, what is the effect at the concrete blend? -
ANS-There is a loss in droop
For elevated curing, what's the preferred method? - ANS-High early
The normal droop for structural lightweight concrete placement is hardly ever more than
ANS-four inches. For reinforcing steel, the minimal clean spacing between parallel bars in a
layer shall be same to the bar diameter but now not much less than _____. - ANS-1 inch
How are the ends of backside bearing joists typically laterally restrained? - ANS-Solid
blockading
How frequently are electricity exams required for concrete? - ANS-At least 1 a day consistent
with one hundred fifty cubic yards or five,000 rectangular feet
In a beam, what is the minimal advocated distance between tendons? - ANS-1-1/2 inches
In a beam, what's the encouraged distance among tendons? - ANS-1-1/2 inches
In a double wythe masonry wall with a 2 inch cavity, what is the desired spacing of reinforcing
metallic ties? - ANS-four-half of rectangular toes
In a strengthened masonry wall the MINIMUM distance among the edge of a vertical reinforcing
bar and any surface of a masonry unit shall be: - ANS-1/4 inch
In an condo building, luminous markings shall be furnished alongside the egress direction while
the occupied flooring are ______ above the lowest level of the hearth branch car get admission
to. - ANS-extra than seventy five feet
What is the most stud spacing in light body production? ANS-24 inches Lowering the pinnacle
bars in a 6-inch deep slab may want to lessen its load carrying ability by using ______. -
ANS-20 percent
On HOUSE wrap how some distance do you lap the edges and ends? - ANS-2 inches on the
edged and six inches on the ends
Radiant warmers may be used so long as they're ANS-36 inches away from combustibles.
What form of soil is sand categorized as? - ANS-Type C The ends of K-Series joists shall
amplify a distance of not much less than ______ over the masonry or concrete help and be
anchored to the metallic bearing plate. - ANS-4 inches
ANS-Class B materials are required for hall wall finishes in a building that is nonspinkled and
has Group B occupancy. Typically, a joist girder isn't always ANS-Bridged. A lintel must have not
less than what number of inches of bearing over the ends of every jamb? - ANS-4 inches
A clean cowl of _____ inches is needed for more than a few eleven reinforcing metal bar in a
precast wall this is exposed to the elements - ANS-three/4. According to code, the subsequent
is NOT considered a dangerous vicinity for the reason of glazing: - ANS-Glazing in egress
window
According to the Americans with Disabilities Act, how massive does the landing need to be at
the lowest of a ramp? - ANS-3 toes by 5 toes
All of the subsequent roofing substances may be re-used except - ANS-combination materials
All of the following soil provisions are considered expansive except for: - ANS-at least 10% of
soil debris are much less than 5 micrometers in length
As the temperature of the concrete mix increases, what is the effect at the concrete blend? -
ANS-There is a loss in droop
For elevated curing, what's the preferred method? - ANS-High early
The normal droop for structural lightweight concrete placement is hardly ever more than
ANS-four inches. For reinforcing steel, the minimal clean spacing between parallel bars in a
layer shall be same to the bar diameter but now not much less than _____. - ANS-1 inch
How are the ends of backside bearing joists typically laterally restrained? - ANS-Solid
blockading
How frequently are electricity exams required for concrete? - ANS-At least 1 a day consistent
with one hundred fifty cubic yards or five,000 rectangular feet
In a beam, what is the minimal advocated distance between tendons? - ANS-1-1/2 inches
In a beam, what's the encouraged distance among tendons? - ANS-1-1/2 inches
In a double wythe masonry wall with a 2 inch cavity, what is the desired spacing of reinforcing
metallic ties? - ANS-four-half of rectangular toes
In a strengthened masonry wall the MINIMUM distance among the edge of a vertical reinforcing
bar and any surface of a masonry unit shall be: - ANS-1/4 inch
In an condo building, luminous markings shall be furnished alongside the egress direction while
the occupied flooring are ______ above the lowest level of the hearth branch car get admission
to. - ANS-extra than seventy five feet
What is the most stud spacing in light body production? ANS-24 inches Lowering the pinnacle
bars in a 6-inch deep slab may want to lessen its load carrying ability by using ______. -
ANS-20 percent
On HOUSE wrap how some distance do you lap the edges and ends? - ANS-2 inches on the
edged and six inches on the ends
Radiant warmers may be used so long as they're ANS-36 inches away from combustibles.
What form of soil is sand categorized as? - ANS-Type C The ends of K-Series joists shall
amplify a distance of not much less than ______ over the masonry or concrete help and be
anchored to the metallic bearing plate. - ANS-4 inches
