PKSC2040 Test 3
1. What are some functional requirements of closures? (5): 1. Contain product
2. Provide barrier
3. Consumer can open the product
4. Tamper evidence
5. Maintain internal pressure
2. What is a positive seal on a closure?: When the closure makes full contact with the land
3. What is the land of a container?: The flat area below the finish to allow the closure to make a positive
seal
4. In what way does a liner or gasket assist a closure?: These features can compensate for
irregularities in the closure and assist in ensuring a positive seal
5. What are some factors that affect the positive seal? (5): 1. Closure material
2. Type of container
3. Flatness of the land
4. Width of land
5. torque required to seal
1/8
,6. Describe a vacuum-tight seal: There is partial pressure in the headspace of the container that keeps
pressure on the inside of the cap. This results from sealing/processing conditions like hot fill products.
7. Describe a high pressure seal: These seals deal with carbonated products such as beer and sodas
that must ensure the closure is very secure
8. Describe a vented closure: These closures allow for a release of pressure at a given interval. Examples
are for produce or coffee.
9. What are the 3 types of closure engagement?: 1. Threaded
2. Friction
3. Push-in
10. What are 3 subcategories of threaded closures?: 1. CT
2. Roll on
3. Press on/twist off
11. What are 2 subcategories of Friction closures?: 1. Crown
2. Snap
12. What are 2 subcategories of push-in closures?: 1. Rubber stopper
2. Cork
2/8
, 13. What are some features of threaded closures?: 1. Most common style
2. Tight seal is dependent on torque and pitch
14. Who decides the styles of finish for CT closures?: GPI
15. What are the names of the 5 critical finish dimensions?: 1. T- Thread
2. I- interior
3. E- Exterior
4. S- "S" (start of thread from top)
5. H- height
16. What is the relationship between cap diameter and torque?: Smaller diameter =
smaller torque
17. What are the two kinds of continuous thread design?: M style and L style
18. What is the difference between and M style and an L style thread design?: M
style has a larger angle on the top than on the bottom while the L style has an equal angle on both sides. M better for
heavier bottles
19. What component is added to a lug cap to achieve a tight seal?: Plastisol
3/8
1. What are some functional requirements of closures? (5): 1. Contain product
2. Provide barrier
3. Consumer can open the product
4. Tamper evidence
5. Maintain internal pressure
2. What is a positive seal on a closure?: When the closure makes full contact with the land
3. What is the land of a container?: The flat area below the finish to allow the closure to make a positive
seal
4. In what way does a liner or gasket assist a closure?: These features can compensate for
irregularities in the closure and assist in ensuring a positive seal
5. What are some factors that affect the positive seal? (5): 1. Closure material
2. Type of container
3. Flatness of the land
4. Width of land
5. torque required to seal
1/8
,6. Describe a vacuum-tight seal: There is partial pressure in the headspace of the container that keeps
pressure on the inside of the cap. This results from sealing/processing conditions like hot fill products.
7. Describe a high pressure seal: These seals deal with carbonated products such as beer and sodas
that must ensure the closure is very secure
8. Describe a vented closure: These closures allow for a release of pressure at a given interval. Examples
are for produce or coffee.
9. What are the 3 types of closure engagement?: 1. Threaded
2. Friction
3. Push-in
10. What are 3 subcategories of threaded closures?: 1. CT
2. Roll on
3. Press on/twist off
11. What are 2 subcategories of Friction closures?: 1. Crown
2. Snap
12. What are 2 subcategories of push-in closures?: 1. Rubber stopper
2. Cork
2/8
, 13. What are some features of threaded closures?: 1. Most common style
2. Tight seal is dependent on torque and pitch
14. Who decides the styles of finish for CT closures?: GPI
15. What are the names of the 5 critical finish dimensions?: 1. T- Thread
2. I- interior
3. E- Exterior
4. S- "S" (start of thread from top)
5. H- height
16. What is the relationship between cap diameter and torque?: Smaller diameter =
smaller torque
17. What are the two kinds of continuous thread design?: M style and L style
18. What is the difference between and M style and an L style thread design?: M
style has a larger angle on the top than on the bottom while the L style has an equal angle on both sides. M better for
heavier bottles
19. What component is added to a lug cap to achieve a tight seal?: Plastisol
3/8