BC SHIFTBOSS | 419 QUESTIONS |
WITH ACCURATE SOLUTIONS!!
, Don't know?
2 of 417
Term
"Who is responsible for examining and checking equipment before
putting it use?"
Give this one a try later!
The Manager. Every 3 months.
The operator. The Manager
Don't know?
3 of 417
Definition
A condition that results from exposure in the workplace, to a
physical, chemical, or biological agent causing impairment to the
worker.
Give this one a try later!
, ""What type of knot is
"Suitable:"
recommended for:"
"What must a manager do with an
"Occupational Illness:"
approved variance to the Code?"
Don't know?
4 of 417
Term
"How are Nonel assemblies connected into a circuit?"
Give this one a try later!
Fuse lines are used to connect Nonel assemblies into a circuit.
Chemical tubes are used to connect Nonel assemblies into a circuit.
Trunkline (detonating cord) is used to connect Nonel assemblies into a
circuit. The type and strength of cord depends on the Nonel assembly
being used.
Electrical wires are used to connect Nonel assemblies into a circuit.
Don't know?
, 5 of 417
Term
"What are requirements of the code in respect to the examination of
workings by a shiftboss or supervisor and the recording of
conditions found?"
Give this one a try later!
a) 30-45 degree slopes
b) A well treed slope
c) Temperature and pressure metamorphosis
d) A triggering device" A well treed slope.
"1. All active workings shall be examined by the certified shiftboss.
2. Before going off shift, shiftboss will record all unusual or dangerous
occurrences.
The shock tube is a hollow plastic tube lined with finely powdered explosives,
when properly initiated it propagates a shock wave to the detonator causing it to
explode.
"1. Shall examine and check the equipment and read the logbook before using
the equipment.
2. Unsafe conditions - Do not operate the equipment unless repairs have been
made.
Don't know?
6 of 417
WITH ACCURATE SOLUTIONS!!
, Don't know?
2 of 417
Term
"Who is responsible for examining and checking equipment before
putting it use?"
Give this one a try later!
The Manager. Every 3 months.
The operator. The Manager
Don't know?
3 of 417
Definition
A condition that results from exposure in the workplace, to a
physical, chemical, or biological agent causing impairment to the
worker.
Give this one a try later!
, ""What type of knot is
"Suitable:"
recommended for:"
"What must a manager do with an
"Occupational Illness:"
approved variance to the Code?"
Don't know?
4 of 417
Term
"How are Nonel assemblies connected into a circuit?"
Give this one a try later!
Fuse lines are used to connect Nonel assemblies into a circuit.
Chemical tubes are used to connect Nonel assemblies into a circuit.
Trunkline (detonating cord) is used to connect Nonel assemblies into a
circuit. The type and strength of cord depends on the Nonel assembly
being used.
Electrical wires are used to connect Nonel assemblies into a circuit.
Don't know?
, 5 of 417
Term
"What are requirements of the code in respect to the examination of
workings by a shiftboss or supervisor and the recording of
conditions found?"
Give this one a try later!
a) 30-45 degree slopes
b) A well treed slope
c) Temperature and pressure metamorphosis
d) A triggering device" A well treed slope.
"1. All active workings shall be examined by the certified shiftboss.
2. Before going off shift, shiftboss will record all unusual or dangerous
occurrences.
The shock tube is a hollow plastic tube lined with finely powdered explosives,
when properly initiated it propagates a shock wave to the detonator causing it to
explode.
"1. Shall examine and check the equipment and read the logbook before using
the equipment.
2. Unsafe conditions - Do not operate the equipment unless repairs have been
made.
Don't know?
6 of 417
